Mark this thread as Unsold
WTS 14” FXR Division MotorWitch bars - wired and heated!
#1
WTS 14” FXR Division MotorWitch bars - wired and heated!
Selling my 14” FXR Division MotorWitch handlebars, already wired and ready to drop on your Road Glide. These are fantastic bars for those who don’t want the typical “F47” style spiked bars that everyone seems to have. They give a perfect view of the boom display as well as the gauges. They are nice and narrow so you aren’t riding with your arms way apart. Very comfortable T-bar/MX bar style hand position.
They fit 2020 RGS’s with only the need to cut two zip ties which hold the clutch line down behind the console. Very easy. There’s even a power connector right there by the other connectors, for the heated grips.
I had these on my 2020 Road Glide Special for about 2 months before deciding I wanted taller, so I ordered 16’inchers and new brake and clutch lines. Whenever I do bars, since I never like pulling wires more then once, I always order a new TBW sensor. So I am selling the 14” bars already wired, with the TBW sensor PN 32700050A installed, H-D heated grips PN 56100034, and both switch harnesses, 69200178 and 69200179 already in the bar. This was in use on my 2020 RDRS equipped Road Glide Special. It’s up to you to determine compatibility with a different model, which is easy to do with any of the online parts diagrams. Also note the clamp area is 1.25’’ which is factory for the 2020 RGS. No adapters needed. However I can’t vouch for other models as some have 1” clamp areas and would require 1.25” clamp risers. You may want to install poly bushings as well - I use alloy art gooden tight bushings, and the H-D poly’s are identical.
All that is needed to install is your original switch packs which disconnect at the connectors (takes 5 seconds) and your levers and related metal. This will turn a 3-4 hour install into about 20 min. A child could do it. Would be a good opportunity to upgrade to lighted switches!
The bars are next to perfect, they are used and have one nick where the extended lever clamp apparently made contact, (shown in photo below) but on a bike that uses the same clamp it won’t be seen. I also put a piece of paint protection film around the left bar as I had a sunglasses case strapped to it. It will peel right off if not needed.
It’s wrapped, boxed and ready to go. $550 delivered, or $500 picked up in Sarasota County, FL.
They fit 2020 RGS’s with only the need to cut two zip ties which hold the clutch line down behind the console. Very easy. There’s even a power connector right there by the other connectors, for the heated grips.
I had these on my 2020 Road Glide Special for about 2 months before deciding I wanted taller, so I ordered 16’inchers and new brake and clutch lines. Whenever I do bars, since I never like pulling wires more then once, I always order a new TBW sensor. So I am selling the 14” bars already wired, with the TBW sensor PN 32700050A installed, H-D heated grips PN 56100034, and both switch harnesses, 69200178 and 69200179 already in the bar. This was in use on my 2020 RDRS equipped Road Glide Special. It’s up to you to determine compatibility with a different model, which is easy to do with any of the online parts diagrams. Also note the clamp area is 1.25’’ which is factory for the 2020 RGS. No adapters needed. However I can’t vouch for other models as some have 1” clamp areas and would require 1.25” clamp risers. You may want to install poly bushings as well - I use alloy art gooden tight bushings, and the H-D poly’s are identical.
All that is needed to install is your original switch packs which disconnect at the connectors (takes 5 seconds) and your levers and related metal. This will turn a 3-4 hour install into about 20 min. A child could do it. Would be a good opportunity to upgrade to lighted switches!
The bars are next to perfect, they are used and have one nick where the extended lever clamp apparently made contact, (shown in photo below) but on a bike that uses the same clamp it won’t be seen. I also put a piece of paint protection film around the left bar as I had a sunglasses case strapped to it. It will peel right off if not needed.
It’s wrapped, boxed and ready to go. $550 delivered, or $500 picked up in Sarasota County, FL.
#3
Fxr division bars -
Selling my 14” FXR Division MotorWitch handlebars, already wired and ready to drop on your Road Glide. These are fantastic bars for those who don’t want the typical “F47” style spiked bars that everyone seems to have. They give a perfect view of the boom display as well as the gauges. They are nice and narrow so you aren’t riding with your arms way apart. Very comfortable T-bar/MX bar style hand position.
They fit 2020 RGS’s with only the need to cut two zip ties which hold the clutch line down behind the console. Very easy. There’s even a power connector right there by the other connectors, for the heated grips.
I had these on my 2020 Road Glide Special for about 2 months before deciding I wanted taller, so I ordered 16’inchers and new brake and clutch lines. Whenever I do bars, since I never like pulling wires more then once, I always order a new TBW sensor. So I am selling the 14” bars already wired, with the TBW sensor PN 32700050A installed, H-D heated grips PN 56100034, and both switch harnesses, 69200178 and 69200179 already in the bar. This was in use on my 2020 RDRS equipped Road Glide Special. It’s up to you to determine compatibility with a different model, which is easy to do with any of the online parts diagrams. Also note the clamp area is 1.25’’ which is factory for the 2020 RGS. No adapters needed. However I can’t vouch for other models as some have 1” clamp areas and would require 1.25” clamp risers. You may want to install poly bushings as well - I use alloy art gooden tight bushings, and the H-D poly’s are identical.
All that is needed to install is your original switch packs which disconnect at the connectors (takes 5 seconds) and your levers and related metal. This will turn a 3-4 hour install into about 20 min. A child could do it. Would be a good opportunity to upgrade to lighted switches!
The bars are next to perfect, they are used and have one nick where the extended lever clamp apparently made contact, (shown in photo below) but on a bike that uses the same clamp it won’t be seen. I also put a piece of paint protection film around the left bar as I had a sunglasses case strapped to it. It will peel right off if not needed.
It’s wrapped, boxed and ready to go. $550 delivered, or $500 picked up in Sarasota County, FL.
They fit 2020 RGS’s with only the need to cut two zip ties which hold the clutch line down behind the console. Very easy. There’s even a power connector right there by the other connectors, for the heated grips.
I had these on my 2020 Road Glide Special for about 2 months before deciding I wanted taller, so I ordered 16’inchers and new brake and clutch lines. Whenever I do bars, since I never like pulling wires more then once, I always order a new TBW sensor. So I am selling the 14” bars already wired, with the TBW sensor PN 32700050A installed, H-D heated grips PN 56100034, and both switch harnesses, 69200178 and 69200179 already in the bar. This was in use on my 2020 RDRS equipped Road Glide Special. It’s up to you to determine compatibility with a different model, which is easy to do with any of the online parts diagrams. Also note the clamp area is 1.25’’ which is factory for the 2020 RGS. No adapters needed. However I can’t vouch for other models as some have 1” clamp areas and would require 1.25” clamp risers. You may want to install poly bushings as well - I use alloy art gooden tight bushings, and the H-D poly’s are identical.
All that is needed to install is your original switch packs which disconnect at the connectors (takes 5 seconds) and your levers and related metal. This will turn a 3-4 hour install into about 20 min. A child could do it. Would be a good opportunity to upgrade to lighted switches!
The bars are next to perfect, they are used and have one nick where the extended lever clamp apparently made contact, (shown in photo below) but on a bike that uses the same clamp it won’t be seen. I also put a piece of paint protection film around the left bar as I had a sunglasses case strapped to it. It will peel right off if not needed.
It’s wrapped, boxed and ready to go. $550 delivered, or $500 picked up in Sarasota County, FL.
Best regards, John
#4
PM me if you want to proceed.
Thanks!
#6
Fxr division bars -
Hi John. The parts diagrams I am looking at show both bikes use the same throttle controller so that would work fine. However you’ll need to confirm if the handlebar clamp area is 1” or 1.25”. The bar requires a 1.25” clamp. If yours is a 1” clamp it won’t fit as-is. You’d have to change the clamp (easy enough).
PM me if you want to proceed.
Thanks!
PM me if you want to proceed.
Thanks!
The following users liked this post:
Mchad (07-02-2021)
Trending Topics
Thread
Thread Starter
Forum
Replies
Last Post
Cosmic Razorback
2014-2023 Touring Models
4
03-11-2019 04:34 PM