What did you do to your bagger today?
Went out to the bike shed and had a couple beers with Her, as it's minus Holy F**k here right now and I have to wait 3 more mths till riding weather arrives!!
The following 3 users liked this post by Harfar:
Had a nice 3 hour ride yesterday knowing today was a snow day. Mid 30's and sunny. Not too bad. 6" of snow on the ground today. I think I'll just sit at home and order rear shocks after too much researching. .
The following 3 users liked this post by chopr147:
Does anyone have the Stock ECM map for a 2008 FLHTCUI in a .mt6 file. I live in Crete, Greece and do not have a dealer that can do this. I am hoping someone saved their original map when they upgraded their bike and was smarter than I was.
Any help would be appreciated
Any help would be appreciated
This has been over the past week but haven’t been on the forum in a while.
andrews 57h cam.
feuling cam plate, oil pump, lifters, and chain tensioners.
Koyo cam bearings.
s&s adjustable pushrods.
replaced AN big sucker w/ DK outlaw 587.
ordered FM crossover pipe (arriving Tuesday).
new map for PC-V.
rattle canned heat shields and mufflers w/ high temp flat black paint.
andrews 57h cam.
feuling cam plate, oil pump, lifters, and chain tensioners.
Koyo cam bearings.
s&s adjustable pushrods.
replaced AN big sucker w/ DK outlaw 587.
ordered FM crossover pipe (arriving Tuesday).
new map for PC-V.
rattle canned heat shields and mufflers w/ high temp flat black paint.
The following 5 users liked this post by Sethcat:
Bhrees (01-08-2022),
cyclone65 (01-08-2022),
Miatsoci (01-08-2022),
Oil, Gas & Leather (01-19-2022),
sox_giantsfan (01-09-2022)
@Sethcat ..looks good. I wish I could say eff my warranty and go outside of SE for a cam. But.. Considering the vast improvements of the 462 over stock.. Even sound.. I'm doing that change in a few weeks on a nice day. 17 degrees today lol. The M8s just don't need radical to be greater.. But ain't nothin ever wrong with radical either. Good luck Bro
The following 2 users liked this post by Miatsoci:
Oil, Gas & Leather (01-19-2022),
Sethcat (07-23-2022)
This diagram shows the difference in available threads between the normal mount hole (top) and dowel hole (bottom).
Dowel hole with stud and nut.
Last edited by Cornpipe; 01-08-2022 at 07:58 AM.
The following users liked this post:
Sethcat (07-22-2022)
New shifter linkage
Out with the old, in with a new one. Lasted 14 years. Took out the shift shaft and cleaned it up. Moisture does get in there.
Last edited by J2X; 01-08-2022 at 08:30 PM.
@Cornpipe thanks! Interesting about the threaded dowels. I did not even know that was an option. Also interesting about the K vs L. I actually bought the cam plate back in 2018 and managed to procrastinate the project until now...
@Miatsoci Thanks and I hear ya about the weather. I am in NOVA freezing in my garage. The cold temps were a pain for the paint too. Pretty sure nothing is dried really. I also don't plan to cure them other than run them on the bike.
@Miatsoci Thanks and I hear ya about the weather. I am in NOVA freezing in my garage. The cold temps were a pain for the paint too. Pretty sure nothing is dried really. I also don't plan to cure them other than run them on the bike.
The following users liked this post:
Oil, Gas & Leather (01-19-2022)
I received my tire pressure sensors for my wheels. Went to order the 41000341F BCM, to complete the system, and the HD web site says no match for those numbers? Anyone have any ideas? Surdike, and the likes can no longer sell HD parts.
Last edited by handirifle; 01-09-2022 at 12:59 AM.