What did you do to your bagger today?
@sabunimwil@gmail.com That's a crazy situation. I had the rear go out and I realized it was happening but tried to push on. Big mistake. You did the right thing stopping. I can't imagine why it would have gone out in so little time though.
The following users liked this post:
sabunimwil@gmail.com (10-15-2021)
If its the bike in his sig, its a '16, so lots of time,, but few miles. Wheel bearings CAN be ruined by excessive water, rain, too much pressure from a hose, or a car wash. Could also have lost a grease seal, or a slow leaking one. Not saying thats the case here, but that bearing looked dry as a bone in the Texas desert. Lol, rust is not a good lubricator.
I have seen guys (not implying Wil did at ALL) take bike to the car wash and power wash the grease off the axle hubs.
I have seen guys (not implying Wil did at ALL) take bike to the car wash and power wash the grease off the axle hubs.
Just ordered a new Freedom shield and ustom Dynamics Fillerz for the saddlebag supports. Prob won't get them till sometime in Nov though.
The following 2 users liked this post by handirifle:
Oil, Gas & Leather (10-26-2021),
T-town (10-16-2021)
Breather & catchcan install
I finished up the breather kit install.
I think it turned out pretty good.
Solid as a rock too, so the motor shouldn't shake it apart.
I think it turned out pretty good.
Solid as a rock too, so the motor shouldn't shake it apart.
The following 6 users liked this post by 07UltraGuy:
Bhrees (10-18-2021),
cyclone65 (10-16-2021),
Fritz Franz (10-25-2021),
Jarhead74 (10-16-2021),
Oil, Gas & Leather (10-26-2021),
and 1 others liked this post.
If its the bike in his sig, its a '16, so lots of time,, but few miles. Wheel bearings CAN be ruined by excessive water, rain, too much pressure from a hose, or a car wash. Could also have lost a grease seal, or a slow leaking one. Not saying thats the case here, but that bearing looked dry as a bone in the Texas desert. Lol, rust is not a good lubricator. I have seen guys (not implying Wil did at ALL) take bike to the car wash and power wash the grease off the axle hubs.
I don't trust Javelina HD and I sincerely doubt they checked that bearing. I trusted then once and it almost cost my wife and me. That's why I've learned to do it myself. If not I take it to Bear at Lost Souls.
That's impressive mileage, and you're doing good work with it too.
That's impressive mileage, and you're doing good work with it too.
The following users liked this post:
sabunimwil@gmail.com (10-17-2021)
I ordered a Freedom shield a little over a week ago, I’m excited to get it.
The following users liked this post:
Oil, Gas & Leather (10-26-2021)
I'm glad it worked out for you Rifle. Let us know your thoughts when you get it installed and test ridden.
The following users liked this post:
Oil, Gas & Leather (10-26-2021)
LOL, I bought a new 2021 Ultra Limited 3 months ago. I have 8,700 mile on her.
Like you, I bought my bike to ride, ya never know what tomorrow brings.
Dress for the slide not the ride. 🙏
Like you, I bought my bike to ride, ya never know what tomorrow brings.
Dress for the slide not the ride. 🙏
Looks solid as hell!!
But I'm curious does the horseshoe shaped tubing behind and on top of the air cleaner screw into the black T- fittings you've made there??
I've been contemplating doing this to my '15 this winter