Fuel Moto Cam Testing results Video Dyno Charts
#1
Thread Starter
|
Platinum Sponsor
Fuel Moto Cam Testing results Video Dyno Charts
As some of you know I have been working on offering cams alongside our Power Packages for the 96" bikes for those who are looking to take the next step in performance. Over the past year I have been studying cam profiles and lobe centers as well as analyzing dyno charts from many of the bikes/builds and combinations we have tuned. We wanted to offer drop in cams with good power gains and most importantly we needed a cam that will complement our components. We have tuned 100's of mismatched combinations that made low or poor numbers and knew we could put together a package and improve on what we typically see. I talked with Bob Woods on several occasions and his straight forward and honest approach to business is a very good fit with ours and most importantly his knowlege of cams is second to none. We talked specifically about a cam for what we were looking for and we both agreed the TW6-6 should be a great fit, especially because our Jackpot mufflers and 2/1/2 headpipe are developed primarily for bottom end torque yet we still wanted a good Hp increase so we got a set to test. We swapped the cams, I loaded a PC-V map for a similar setup that we tuned and took the bike for a 15 minute ride with the PC-V/Auto Tune enabled. I could immediately feel the difference in performance, bottom end torque was smooth and signifigantly increased and the throttle response is much better with greatly increased overall power. Idle has a bit of a loap and sounds more agressive. The cams and valvetrain are as quiet as stock, overall the bike ran very well with our PC-V base map and Auto Tune. Got back to the shop and plugged into a laptop to view the fuel trims and was impressed that the Auto Tune had made changes to the base map almost identical to what I was expecting. The Auto Tune is one of the single most powerful tuning tools available and really works well. Put it up on the dyno and spent a few hours datalogging and tuning the fuel and igntion timing tables and the final numbers were 93Hp/103Tq. The torque is very strong from 2000 RPM's especially in the 3K RPM range. This testing was done on a 09 Touring models and the combination consists of Woods TW6-6 cams, Jackpot Dyno Tuned mufflers, Jackpot 2/1/2 headpipe, Fuel Moto Stage 1 air cleaner, and Dynojet PC-V (Auto Tune optional) Came in the next day, got the bike up to operating temp made some runs and laid down the same numbers.
http://www.youtube.com/watch?v=Oai8aF6iTw4
http://www.youtube.com/watch?v=6SPs6-pPhqE
http://www.youtube.com/watch?v=Oai8aF6iTw4
http://www.youtube.com/watch?v=6SPs6-pPhqE
__________________
Jamie Long / Fuel Moto USA
The USA's Leader V-Twin EFI & Performance www.fuelmotousa.com
Contact 920-423-3309
Email jamie@fuelmotousa.com
Jamie Long / Fuel Moto USA
The USA's Leader V-Twin EFI & Performance www.fuelmotousa.com
Contact 920-423-3309
Email jamie@fuelmotousa.com
Last edited by fuelmoto; 11-19-2009 at 12:02 PM.
#6
Thread Starter
|
Platinum Sponsor
#7
Outstanding HDF Member
I'd be VERY interested to see what those cams would do with my own set-up. If/when do you plan on starting to handle the cam end of things Jamie? The minute you do, I'd be in a hurry to take the couple hour ride North to have you install them for me and then dyno tune it for me and then program my PCV. Any ideas of ballpark expense for this?
Trending Topics
#8
#10
Thread Starter
|
Platinum Sponsor
I'd be VERY interested to see what those cams would do with my own set-up. If/when do you plan on starting to handle the cam end of things Jamie? The minute you do, I'd be in a hurry to take the couple hour ride North to have you install them for me and then dyno tune it for me and then program my PCV. Any ideas of ballpark expense for this?