Touring Models Road King, Road King Custom, Road King Classic, Road Glide, Street Glide, Electra Glide, Electra Glide Classic, and Electra Glide Ultra Classic bikes.
Sponsored by:
Sponsored by:

09 Street Glide won’t start

Thread Tools
 
Search this Thread
 
  #11  
Old 04-02-2020, 06:27 PM
DanHappy's Avatar
DanHappy
DanHappy is offline
Seasoned HDF Member
Join Date: Jun 2012
Location: Pittsburgh, Pa
Posts: 14,436
Received 2,419 Likes on 1,614 Posts
Default

Hmmm... did you ask the guy if he did anything? Sounds like he could of did something and screwed it up. Ould he of tried to jump it with a car / truck and fry the ecm?
 
  #12  
Old 04-03-2020, 10:16 AM
Fozy490's Avatar
Fozy490
Fozy490 is offline
4th Gear
Thread Starter
Join Date: Mar 2020
Location: Pulaski PA
Posts: 8
Likes: 0
Received 0 Likes on 0 Posts
Default

When I went to pick the bike up, my buddy had the bike on the charger. he connected the charger positive to positive and negative to negative. Said to didn't charge at all. He said he looked at the directions on his charger and it said to connect the negative charge clamp to the frame or body. I've never heard of a charger like that. Could that have fried the ECM?
 
  #13  
Old 04-03-2020, 11:10 AM
Fireball Jack's Avatar
Fireball Jack
Fireball Jack is offline
Stellar HDF Member
Join Date: Oct 2015
Location: Puyallup, wa
Posts: 2,656
Received 842 Likes on 579 Posts
Default

As long as the ground wires are clean and tight it doesnt matter.
 
  #14  
Old 04-03-2020, 11:18 AM
Dan89FLSTC's Avatar
Dan89FLSTC
Dan89FLSTC is online now
Seasoned HDF Member
Veteran: Navy
Join Date: May 2008
Location: South Carolina
Posts: 18,635
Received 9,425 Likes on 5,020 Posts
Default

Originally Posted by Fozy490
He said he looked at the directions on his charger and it said to connect the negative charge clamp to the frame or body. I've never heard of a charger like that. Could that have fried the ECM?
That is the old school way of connecting charger cables and jumper cables, the process is to connect the positive cable first, then connect the negative cable to the frame, that way if there is a spark, it is not near the battery.

Sparks near a battery can be dangerous, especially if the battery has just been under a load.

Connecting the charger cables to the battery posts would not damage the ecm.

 

Last edited by Dan89FLSTC; 04-03-2020 at 11:26 AM.
  #15  
Old 04-03-2020, 12:20 PM
DanHappy's Avatar
DanHappy
DanHappy is offline
Seasoned HDF Member
Join Date: Jun 2012
Location: Pittsburgh, Pa
Posts: 14,436
Received 2,419 Likes on 1,614 Posts
Default

Any way to check to make sure the ECM is fine? Besides of course having it start? lolol
 
  #16  
Old 04-03-2020, 01:11 PM
Fozy490's Avatar
Fozy490
Fozy490 is offline
4th Gear
Thread Starter
Join Date: Mar 2020
Location: Pulaski PA
Posts: 8
Likes: 0
Received 0 Likes on 0 Posts
Default

I emailed Thunder-Max and they said that I can mail it to them and they will check it out, but they are working from home right now and might be a few weeks before I get an answer. They also said that I can take it to a certified installer and most of them have the capability to run a diagnostic on them. Other then that, I have no idea what to do. This is why I ride a dyna haha. less wires, less problems.
 
  #17  
Old 04-03-2020, 02:05 PM
memphisharley's Avatar
memphisharley
memphisharley is offline
Road Warrior
Veteran: Marine Corp
Join Date: Sep 2017
Location: memphis
Posts: 1,926
Received 466 Likes on 356 Posts
Default

battery. check while attempting to crank and note the voltage
 

Last edited by memphisharley; 04-03-2020 at 02:06 PM.
The following users liked this post:
DanHappy (04-03-2020)
  #18  
Old 04-04-2020, 12:24 PM
Fozy490's Avatar
Fozy490
Fozy490 is offline
4th Gear
Thread Starter
Join Date: Mar 2020
Location: Pulaski PA
Posts: 8
Likes: 0
Received 0 Likes on 0 Posts
Default

So I just realized that I can plug my thunder max into my computer. I was hoping that maybe it just needed an update. Or even reset. I downloaded the thunder max program and attempted to plug the thunder max into my computer but it won’t establish a connection. Found some videos online about “initializing” the thunder max after the battery has been disconnected. So I go through the process of 20 seconds ignition one and 20 seconds ignition off. But still no connectivity.
 
  #19  
Old 04-04-2020, 02:04 PM
DanHappy's Avatar
DanHappy
DanHappy is offline
Seasoned HDF Member
Join Date: Jun 2012
Location: Pittsburgh, Pa
Posts: 14,436
Received 2,419 Likes on 1,614 Posts
Default

Hooking via bluetooth?

So your thinking the ecm is fine but the tuner is fried? If that could be wrong, omit it from the circuit.
 
  #20  
Old 04-04-2020, 02:15 PM
Steve Cole's Avatar
Steve Cole
Steve Cole is offline
HD EFI Guru
Join Date: Jan 2008
Posts: 4,000
Received 3,688 Likes on 1,670 Posts
Default

Originally Posted by Fozy490
It’s not my bike. I run a 15 street bob. I barrow my buddies 09 street glide for my longer trips. He bout it used two years ago. As far as I can tell, the previous owner put in a thundermax, and Rinehart slip ons. I used it last May for a ride to Illinois from PA and had no issues. He rode it a few times the following fall and again in January on a random nice day. No issues at all. I go to pick it up to do the oil and general service for my upcoming Illinois run, turn the ignition to ride it to the tailer and nothing. No fuel or spark. Everything lights up. Radio works. Security system works.
The Fuel Pump is controled by the BCM. The ECM talks to the BCM when the key is first turned on and thells the BCM to turn the pump on for about 2 seconds. If the bike does not do that then its a ECM or BCM issue. The fact that you can hot wire the relays says the wiring is fine, except for the wire to the relay. So you can remove the relay and check the voltage at the pin in the relay plug for voltage when you turn the key on and then work back from there. If the bike has key fob's try a new battery in them too.
 


Quick Reply: 09 Street Glide won’t start



All times are GMT -5. The time now is 03:24 PM.