Performance baggers
#651
Well done - like watching the progress you've made.
Its probably been said already but I can't find it, but what height slingshots do you have on this bike?
Thanks
Its probably been said already but I can't find it, but what height slingshots do you have on this bike?
Thanks
The following users liked this post:
ORider (05-20-2020)
#653
I am wanting to add the fog lights that harley offers to my ride. My problem is that I no longer have the gauge nacelle where the switch should go. Any of you guys add these fog lights or any thing that would have required making use of the switches in the nacelle that you also no longer have? If so, how did you go about adding a switch for this type operation?
https://www.amazon.com/dp/B071ZPX32N/?coliid=I3TGPRH5RLSXFG&colid=272XWHO77FIIT&psc=1&ref_=lv_ov_lig_dp_it
wiring harnesses. I had to cut the wires and reconnect them under the seat, coming from the battery, but it works flawless and haven't had any problems with it. I drilled a separate hole into the side of the dash right next to the speedo for the on/off switch. I used a gasket to make it water tight. I'm sure you could mount the switch somewhere convenient. I've seen people mount a switch under the seat to make it not so noticeable. I've heard of people wiring lights directly to their high beams. I'm not that knowledgeable to figure out what the hig/low beam wiring was so I did a separate dedicated light switch. I'm planning on adding fog lights to the RG as well and doing the same wiring harness.
Hope this helps.
The following users liked this post:
blueangel73 (05-04-2020)
#654
The following 2 users liked this post by 23Seven:
ORider (05-20-2020),
SoCalDyna2015 (05-13-2020)
#655
Hey Man, I added a LED Light bar to my dyna a while back. I used one of these https://www.amazon.com/dp/B071ZPX32N...v_ov_lig_dp_it wiring harnesses. I had to cut the wires and reconnect them under the seat, coming from the battery, but it works flawless and haven't had any problems with it. I drilled a separate hole into the side of the dash right next to the speedo for the on/off switch. I used a gasket to make it water tight. I'm sure you could mount the switch somewhere convenient. I've seen people mount a switch under the seat to make it not so noticeable. I've heard of people wiring lights directly to their high beams. I'm not that knowledgeable to figure out what the hig/low beam wiring was so I did a separate dedicated light switch.
I'm planning on adding fog lights to the RG as well and doing the same wiring harness.
Hope this helps.
I'm planning on adding fog lights to the RG as well and doing the same wiring harness.
Hope this helps.
#656
The following users liked this post:
SoCalDyna2015 (05-13-2020)
#657
Last edited by SoCalDyna2015; 05-04-2020 at 05:46 PM.
#658
#659
I’ll play
2011 FLHR
RWD fxrp fairing
fxr style side covers
racing bros 25mm cartridge kit
ohlins 357 rears
s&s 551’s
RR3 exhaust
PV with a FM tune
OG bar and risers
few other nick nacks
not installed yet (can’t get to the shop with covid)
radial calipers
wave rotors and matching pads
HPi intake
2011 FLHR
RWD fxrp fairing
fxr style side covers
racing bros 25mm cartridge kit
ohlins 357 rears
s&s 551’s
RR3 exhaust
PV with a FM tune
OG bar and risers
few other nick nacks
not installed yet (can’t get to the shop with covid)
radial calipers
wave rotors and matching pads
HPi intake
Last edited by JonnyVegas; 05-07-2020 at 05:45 PM.
#660
Bikes looking great!!
I’ll play
2011 FLHR
RWD fxrp fairing
fxr style side covers
racing bros 25mm cartridge kit
ohlins 357 rears
s&s 551’s
RR3 exhaust
PV with a FM tune
OG bar and risers
few other nick nacks
not installed yet (can’t get to the shop with covid)
radial calipers
wave rotors and matching pads
HPi intake
2011 FLHR
RWD fxrp fairing
fxr style side covers
racing bros 25mm cartridge kit
ohlins 357 rears
s&s 551’s
RR3 exhaust
PV with a FM tune
OG bar and risers
few other nick nacks
not installed yet (can’t get to the shop with covid)
radial calipers
wave rotors and matching pads
HPi intake
The following 3 users liked this post by gartec81: