TOAK- Thread Of All Knowledge- Part V
#9421
I see. Well, he gets a pass then.
Shakedown run over. WOOHOO! No runs, no drips, no errors! And no noise!!!
I also have to say a little bump in compression was acquired as the cams came on a little sooner.
Shakedown run over. WOOHOO! No runs, no drips, no errors! And no noise!!!
I also have to say a little bump in compression was acquired as the cams came on a little sooner.
#9422
Can someone explain what the top end tapping/ticking is and on what motor?
And what the Rockouts do?
Gave up on being an audiophile, going partially deaf and blowing out 2 of the 3 amps I had in the tri amp system finally got to spendy to keep up.
Home theater now has a set (5) of JBL studio 38's with some minor mods and a SVS sub.
Yamaha receiver, Oppo CD player and assorted knickknacks from over the years, nothing on the WG though, not much for music while I ride.
Did finally remember I still have the stock tubes and if I can find them I should be able to see if I can cut them done a bit.
I have nothing good to say about the indians, they're netting spawning fish here and use the sovereign nation bullshit to keep doing it, but the BIA has spent billions on them.
Have a good day all.
Al
And what the Rockouts do?
Gave up on being an audiophile, going partially deaf and blowing out 2 of the 3 amps I had in the tri amp system finally got to spendy to keep up.
Home theater now has a set (5) of JBL studio 38's with some minor mods and a SVS sub.
Yamaha receiver, Oppo CD player and assorted knickknacks from over the years, nothing on the WG though, not much for music while I ride.
Did finally remember I still have the stock tubes and if I can find them I should be able to see if I can cut them done a bit.
I have nothing good to say about the indians, they're netting spawning fish here and use the sovereign nation bullshit to keep doing it, but the BIA has spent billions on them.
Have a good day all.
Al
#9423
Awesome!!
Thanks again
Thanks again
__________________
NO, they DON'T all do that!
ROCKOUT rocker shaft inserts... make the tapping STOP! From the guy that FOUND and CURED the problem NO ONE ELSE COULD, thank you for your support!
Ordering & info http://www.rockout.biz On ebay! ... CLICK HERE
Also on amazon.com...
Imitated, never equaled... ROCKOUTS!
Ordering & info http://www.rockout.biz On ebay! ... CLICK HERE
Also on amazon.com...
Imitated, never equaled... ROCKOUTS!
#9424
Don't want to turn this place into a commercial... my website below has the details, PM me if you have any questions.
#9425
Al, basically there is loose tolerances between the rocker shafts and the rocker shaft support bolts allowing the shafts to rotate and slam against the bolts and create a tapping sound. The inserts create a closer fit and eliminate the tapping and the "sewing machine" sound.
#9426
Interesting. Thanks. I need to start to look for ideas on what works. It's funny how some guys want a real clear system, so they tune it and think it's a sealed room. Like a car. It's open to the air and when moving, you have air noise. So it's impossible to compare a car and a bike. Nuts.
John, This is the TOAK. Knowledge, humor, and nearly nekkid women (not necessarily in that order of course) is what we crave.
#9427
Join Date: Jan 2011
Location: Southeast Michigan 15 Minutes East Of Hell
Posts: 149,135
Received 49,835 Likes
on
19,328 Posts
Ear buds man. I use the $29 Sonys and listen to the music on my phone. Less wind noise, less roar from the pipes, I can actually hear the music, and (the big one for me) my head is not ringing like a damn bell at the end of a few hours ride on the slab.
John, This is the TOAK. Knowledge, humor, and nearly nekkid women (not necessarily in that order of course) is what we crave.
John, This is the TOAK. Knowledge, humor, and nearly nekkid women (not necessarily in that order of course) is what we crave.
#9428
Got it... thanks
#9430
Join Date: Jan 2011
Location: Southeast Michigan 15 Minutes East Of Hell
Posts: 149,135
Received 49,835 Likes
on
19,328 Posts
The air is gettin' really thin in da U.P. :>)