3 Inch extensions for forward controls 04 to 08
#1
3 Inch extensions for forward controls 04 to 08
I have officially got all my parts back from the powder coater and have most of em packaged up.
These will only work on 04 and newer models with forward controls already added. These will not work with stock headers so make sure you have room 3 inches in front of the stock location for these. Pipes like short shots are no problem since they run behind the stock location, I will not say for sure if these will work with certain pipes because there are to many pipes out there and I have only used them on my nightster with short shots. I will look into any questions you may have concerning fitment. Contact me @ MillCityMachine@gmail.com
Included is 2 extension plates 2 support rods 1 shift rod 1 brake rod all zinc plated hardware and zinc plated ball joints. All parts are steel powder coated black and PROUDLY MADE IN THE USA [sm=usa.gif] [sm=usa.gif] [sm=usa.gif]
225 shipped in the USA
Before Keep in mind these extensions will not raise your feet up just out. CableDawg318s bike is on its kick stand, which makes it look higher
After
Here I am showing the stock forward control. Note how close the peg is to the ehaust.
After setting up the miller I ran off 2 new brackets Gata love machines
And......TA DA!...... Nice looking brackets to replace the beat up hacked one.
This is the end to the new brake rod. Sorry for the terrible picture, I wanted to show a picture of the whole brake rod but its 21 inches long 3 inches longer than stock and it wouldnt all fit in the cameras view.
sorry if the pics are bad but there off my camera phone [sm=smiley21.gif]
These will only work on 04 and newer models with forward controls already added. These will not work with stock headers so make sure you have room 3 inches in front of the stock location for these. Pipes like short shots are no problem since they run behind the stock location, I will not say for sure if these will work with certain pipes because there are to many pipes out there and I have only used them on my nightster with short shots. I will look into any questions you may have concerning fitment. Contact me @ MillCityMachine@gmail.com
Included is 2 extension plates 2 support rods 1 shift rod 1 brake rod all zinc plated hardware and zinc plated ball joints. All parts are steel powder coated black and PROUDLY MADE IN THE USA [sm=usa.gif] [sm=usa.gif] [sm=usa.gif]
225 shipped in the USA
Before Keep in mind these extensions will not raise your feet up just out. CableDawg318s bike is on its kick stand, which makes it look higher
After
Here I am showing the stock forward control. Note how close the peg is to the ehaust.
After setting up the miller I ran off 2 new brackets Gata love machines
And......TA DA!...... Nice looking brackets to replace the beat up hacked one.
This is the end to the new brake rod. Sorry for the terrible picture, I wanted to show a picture of the whole brake rod but its 21 inches long 3 inches longer than stock and it wouldnt all fit in the cameras view.
sorry if the pics are bad but there off my camera phone [sm=smiley21.gif]
#2
#3
RE: 3 Inch extensions for forward controls 04 to 08
I understandthere are too many brands and models of pipes to comment on each , but,... so far the pipes I see have a swept back bend behind the front peg, whereas my rinehart bends in front of the fwd controls, there is some room but not much- have you had feedback from a person whose pipe bends closer to the front axle than the rear
[IMG]local://upfiles/47624/49C545BC368C4B6AA99821B20200AB40.jpg[/IMG]
[IMG]local://upfiles/47624/49C545BC368C4B6AA99821B20200AB40.jpg[/IMG]
#4
RE: 3 Inch extensions for forward controls 04 to 08
ORIGINAL: Kozak
I understandthere are too many brands and models of pipes to comment on each , but,... so far the pipes I see have a swept back bend behind the front peg, whereas my rinehart bends in front of the fwd controls, there is some room but not much- have you had feedback from a person whose pipe bends closer to the front axle than the rear
[IMG]local://upfiles/47624/49C545BC368C4B6AA99821B20200AB40.jpg[/IMG]
I understandthere are too many brands and models of pipes to comment on each , but,... so far the pipes I see have a swept back bend behind the front peg, whereas my rinehart bends in front of the fwd controls, there is some room but not much- have you had feedback from a person whose pipe bends closer to the front axle than the rear
[IMG]local://upfiles/47624/49C545BC368C4B6AA99821B20200AB40.jpg[/IMG]
Judging by the pic I dont think they will fit. Best bet is to picture the stock peg three inches further up and se if theres room. A simple tape measure will tell you.
#7