Crossbones Pictures
#1151
#1152
They are US Military aviator night vision goggle cases. Air tight, and water proof...and only $30 each.
I've taken them on a couple trips now, both in the pouring rain, and everything was perfectly dry inside.
I've taken them on a couple trips now, both in the pouring rain, and everything was perfectly dry inside.
#1153
#1154
Honestly...check out Road6Customs bars. Same style bars...half price. I can't see paying $300.00 for a RSD bars...and have to buy their risers as well. RSD makes some cool stuff...but the prices are recockulous...
Road6customs are direct bolt on....
Road6customs are direct bolt on....
I want to put RSD Vintage bars on my 2008 Crossbones and noticed that RSD says that the bars are not for use with the Crossbones OEM risers. As it turns out the risers are too big and will not fit within the 7" crossbar. However the sales rep did say that RSD risers would fit. He went on to say that I may need new riser studs that convert fine thread (1/2x20) to course thread (1/2x13).
Here is the part the rep referenced:
- Options: Fine Thread 1/2-20 or Dual Thread 1/2-20 x 1/2-13(shown)
- Length: 2.5 inches
- Fits: Fine - 1/2-20 thread pitch Risers for springers; Dual - 1/2-13 thread pitch Risers for springers
- Finish: Steel or Black
The rep wasn't sure if the OEM studs had fine thread, but he says after-market springers do. I could always tear mine down and look for myself, but I thought I might save myself the aggravation by seeing if anyone here is running these bars and whether new riser studs were required.
Here is the part the rep referenced:
- Options: Fine Thread 1/2-20 or Dual Thread 1/2-20 x 1/2-13(shown)
- Length: 2.5 inches
- Fits: Fine - 1/2-20 thread pitch Risers for springers; Dual - 1/2-13 thread pitch Risers for springers
- Finish: Steel or Black
The rep wasn't sure if the OEM studs had fine thread, but he says after-market springers do. I could always tear mine down and look for myself, but I thought I might save myself the aggravation by seeing if anyone here is running these bars and whether new riser studs were required.
#1155
Rsd bars
I put RSD short stacks on my crossbones and they fit with the factory risers. I did use some longer bolts to make sure the riser caps tightened down properly.
#1157
This is my cross bones, 2008, paughco bell tip exhaust, high five mach 2 air cleaner, vintage horn, small black rond mirrors and so on
http://www.servimg.com/image_preview...428&u=12651387
http://www.servimg.com/image_preview...428&u=12651387
Last edited by captainfifi; 09-12-2012 at 09:08 AM.
#1158
Here is mine after the diet
http://instagr.am/p/PYZZw7SRrN/
http://instagr.am/p/Ph103hSRhS/
http://instagr.am/p/Ph1lT-SRhE/
http://instagr.am/p/PYZZw7SRrN/
http://instagr.am/p/Ph103hSRhS/
http://instagr.am/p/Ph1lT-SRhE/
Last edited by taino; 09-13-2012 at 04:00 PM.
#1159
Here is mine after the diet
http://instagr.am/p/PYZZw7SRrN/
http://instagr.am/p/PYZZw7SRrN/