What did you do to Your Softail Today?
#7671
The instructions are a bit vague in that regard.. they say "find the yellow and green traced wire in the harness on the left side" but that wire continues from the rear coil.. track it back to the wire pack that goes to your rear coil and all three wires you need are there.. I disconnected thenconnectornfom the rearr coil and taped it up and hid it behidn the frame rail.. ran ground toframe bolt and green to tach green.
The following users liked this post:
Mallard Slayer (01-26-2019)
#7672
Installed my Venture Heat wiring harness. Pretty simple aside from fitting my fingers in the battery box area to release the cover. Then I rode it like I stole it with my heated jacket liner under my leather. 38-43 degrees where I rode with 80 miles of fast highway and country roads mixed. What a rush! Now I know I can be toasty warm and comfortable while adding to my riding seasons which will be all four now as long as no wet salt is coating road.
Afterwards I cleaned the bike real good and put a blankie on until next ride.
Afterwards I cleaned the bike real good and put a blankie on until next ride.
The following users liked this post:
soldierbot (01-27-2019)
#7673
#7674
The following 2 users liked this post by Maltesefalcon:
GarageJockey (01-28-2019),
soldierbot (01-28-2019)
#7676
#7677
Added wiring harness for heated gear to battery on 2018 FLHCS (Heritage). PITA the first time, but should be no big deal the next time. This video was of some help and may help you, too.
I got some Hot Wired heated glove liners. Did not want to mess with a controller. After hooking up the harness, I rand the gloves for about 5 minutes. NICE.
I got some Hot Wired heated glove liners. Did not want to mess with a controller. After hooking up the harness, I rand the gloves for about 5 minutes. NICE.
#7678
The following users liked this post:
Maltesefalcon (01-28-2019)
#7679
The emblems are on page 804 of the 2019 Parts & Accessories catalog.
Those emblems appear to be PN #61814-55T and you will need
the adapter kit #61840-94T
You can download the '19 P&A catalog here
https://www.harley-davidson.com/us/e...a-catalog.html
hth,
T.
Those emblems appear to be PN #61814-55T and you will need
the adapter kit #61840-94T
You can download the '19 P&A catalog here
https://www.harley-davidson.com/us/e...a-catalog.html
hth,
T.
#7680
Baby Shark!
I put factory floorboards in place of pegs on my Sport Glide which I’ve turned into a lighter version of a road glide.
I think I’m pretty much done with cosmetics.
I’d like to get a little more power outta M8 with cam swap some time in the future....
I think it came out pretty decent.
I used the floorboards extension (from DK CUSTOM) to move them out a little from the factory location. Much more natural position of feet=comfortable...
Heel shifter added as well.
With the peg set up & hard lowers, brake pedal was really tight fit. But with floorboards, it gave me a little more room.
I think I’m pretty much done with cosmetics.
I’d like to get a little more power outta M8 with cam swap some time in the future....
I think it came out pretty decent.
I used the floorboards extension (from DK CUSTOM) to move them out a little from the factory location. Much more natural position of feet=comfortable...
Heel shifter added as well.
With the peg set up & hard lowers, brake pedal was really tight fit. But with floorboards, it gave me a little more room.
The following users liked this post:
soldierbot (01-28-2019)