What did you do to Your Softail Today?
08-20-2023 | 06:08 AM
3rd Gear
Joined: Aug 2023
Posts: 7
Likes: 2
From: Essex, UK
That would be great if you could! I have just installed 31/2 pullback risers to make me sit upright in an effort to just see over the screen (Im 56) and its still annoyingly in my preferred field of vision! Did 11/2 make alit of difference for you? Thanks for all your help
08-20-2023 | 09:26 PM
Cruiser
Joined: Dec 2018
Posts: 147
Likes: 148
From: NE Nebraska
Took her out for the fist trip since big bore install. Approximately 200 miles, keeping in mind the manufacturers break-in recommendation. Wasn't sure how the CV Performance Turner would affect the MPG, but to my surprise I got 42 MPG's... Ran very well, no issues and while I didn't push it, she pulled strong when I called on her to get around a vehicle or truck. Very pleased with the early results. Also, would recommend AMS MotoMachine & Supply to anyone looking for affordable Cubic-Inches...
Last edited by brapple; 08-20-2023 at 10:15 PM.
The following users liked this post:
carl418 (08-20-2023)
08-21-2023 | 05:09 AM
Outstanding HDF Member
Joined: Mar 2018
Posts: 2,773
Likes: 2,258
From: Ft. Wayne IN
That would be great if you could! I have just installed 31/2 pullback risers to make me sit upright in an effort to just see over the screen (Im 56) and its still annoyingly in my preferred field of vision! Did 11/2 make alit of difference for you? Thanks for all your help
See below for some guidance. I used two new mill bastard files (one coarser than the other) to do most of the smoothing out of the cut marks then moved to sandpaper and a wooden block. I put a small chamfer on the edges with the sandpaper. I did not bother with the ultra fine grades. Keep the tape in place on both sides while finishing. Took me about 1.5 hours total time.
cut polycarbonate winshield - Google Search
08-21-2023 | 05:11 AM
3rd Gear
Joined: Aug 2023
Posts: 7
Likes: 2
From: Essex, UK
Sorry; I tried to get a closeup of the edge of the cut-down windshield edge, but my Samsung phone is not capable. Yes, the 1.5" removal did wonders on the height. I'm about 5'8" tall. You may want to go as far as 2", but I'd start with 1.5".
See below for some guidance. I used two new mill bastard files (one coarser than the other) to do most of the smoothing out of the cut marks then moved to sandpaper and a wooden block. I put a small chamfer on the edges with the sandpaper. I did not bother with the ultra fine grades. Keep the tape in place on both sides while finishing. Took me about 1.5 hours total time.
cut polycarbonate winshield - Google Search
See below for some guidance. I used two new mill bastard files (one coarser than the other) to do most of the smoothing out of the cut marks then moved to sandpaper and a wooden block. I put a small chamfer on the edges with the sandpaper. I did not bother with the ultra fine grades. Keep the tape in place on both sides while finishing. Took me about 1.5 hours total time.
cut polycarbonate winshield - Google Search
08-21-2023 | 03:47 PM
Stellar HDF Member
Joined: Sep 2022
Posts: 2,067
Likes: 1,704
From: Florida
The following 10 users liked this post by Rains2much:
BikerPepe` (08-22-2023),
Bopple Hill Rd (08-22-2023),
Chris2fur (08-21-2023),
Dogs57 (08-23-2023),
hattitude (08-22-2023),
and 5 others liked this post.
08-22-2023 | 06:11 PM
The following 2 users liked this post by Hog Augie:
BikerPepe` (08-23-2023),
hattitude (08-22-2023)
08-22-2023 | 06:53 PM
Stellar HDF Member
Joined: Jan 2019
Posts: 2,825
Likes: 1,971
From: Mostly Florida, some Michigan
08-22-2023 | 07:31 PM
Seasoned HDF Member
Joined: Sep 2008
Posts: 11,813
Likes: 8,305
From: San Diego, CA
08-23-2023 | 05:37 AM
Tourer
Joined: Jul 2019
Posts: 393
Likes: 332
From: Lithgow NSW Australia
I know the feeling. Early NYE 2019 I got a message from a mate saying it was heading my way. Had time to load up 3 bikes (lost 3) and get out before it got everything and 97 other homes in my village.
Hoping you and all members are safe.
Cheers
