quick football A/C insert question
#11
#12
A lot of Dyna riders have done that after member WS6 Formula started it a few years ago. The one in my sig pic is mounted on a plain round cover, or it can be run open. (Edit: Mudpuddle did these for a bunch of guys a couple of years back, but he no longer does them for others)
Here's a couple of threads (the second one with video):
https://www.hdforums.com/forum/dyna-...?highlight=ws6
https://www.hdforums.com/forum/dyna-...echroming.html
Also, member Pig in a blanket stuck just the trim ring on a round chrome cover for a similar effect.
Here's a couple of threads (the second one with video):
https://www.hdforums.com/forum/dyna-...?highlight=ws6
https://www.hdforums.com/forum/dyna-...echroming.html
Also, member Pig in a blanket stuck just the trim ring on a round chrome cover for a similar effect.
Last edited by Dawg Rider; 03-06-2011 at 10:51 AM.
#13
A/C Insert carved out. huzzah.
from the typical football cover:
to a nice clean cutout:
I followed these directions up until where you start cutting:
https://www.hdforums.com/forum/2909122-post642.html
since I don't have a die grinder, I used a Dremel tool @ 30,000RPM with a reinforced cutting blade, which ran through the aluminum of the cover like butter.. and since I don't have an angle grinder, or a drill press (though my neighbor does but he was at work).. i filed down the edges and evened it all out by hand.. it actually was pretty easy and took maybe 2 hours total.. since i was doing it all by hand and all.. then shot the edges up with some close-as-can-be color matching engine enamel to prevent rust.. i thought she turned out quite good actually..
edit..Ps thanks for the link Dawg Rider..
to a nice clean cutout:
I followed these directions up until where you start cutting:
https://www.hdforums.com/forum/2909122-post642.html
since I don't have a die grinder, I used a Dremel tool @ 30,000RPM with a reinforced cutting blade, which ran through the aluminum of the cover like butter.. and since I don't have an angle grinder, or a drill press (though my neighbor does but he was at work).. i filed down the edges and evened it all out by hand.. it actually was pretty easy and took maybe 2 hours total.. since i was doing it all by hand and all.. then shot the edges up with some close-as-can-be color matching engine enamel to prevent rust.. i thought she turned out quite good actually..
edit..Ps thanks for the link Dawg Rider..
#15
Im running the Arlen Ness Big Sucker Stage I, and its just a standard K&N filter on there, PN HD-0800
http://www.amazon.com/HD-0800-Replac.../dp/B000FGCYT4
and as long as you have a steady hand, the mod is really easy to do.. the aluminum cuts like buttah..
http://www.amazon.com/HD-0800-Replac.../dp/B000FGCYT4
and as long as you have a steady hand, the mod is really easy to do.. the aluminum cuts like buttah..
#16
Im running the Arlen Ness Big Sucker Stage I, and its just a standard K&N filter on there, PN HD-0800
http://www.amazon.com/HD-0800-Replac.../dp/B000FGCYT4
and as long as you have a steady hand, the mod is really easy to do.. the aluminum cuts like buttah..
http://www.amazon.com/HD-0800-Replac.../dp/B000FGCYT4
and as long as you have a steady hand, the mod is really easy to do.. the aluminum cuts like buttah..
Sweet, thanks!
#18
Thread
Thread Starter
Forum
Replies
Last Post