Calling all FatBoy Lo Owners
#3081
06-14-2011, 04:29 PM
Advanced
For the 1k service, just make sure your neck bearing is seating properly. They tend to settle after the factory install and you will get the wobble effect going around 40-50 mph. Mine did that, I took it to a local bike shop for my 1k service. They didn't check for it. I finally took it to a HD Dealer and they said it should have been checked during the 1k inspection. I already had 7k on my bike by the time I had it fixed.
#3082
06-14-2011, 05:07 PM
Tourer
Join Date: Jun 2011
Location: Florida
Posts: 463
Likes: 0
Received 0 Likes
on
0 Posts
Gotta figure out what to do with those damn holes!!!!
save some $$$, i saw someone else use these
http://www.jeeperz-creeperz.com/fend...sh-p-7847.html
willing to splurge? there's always this
http://www.customchrome.net/icatalog/Full.aspx?Page=368
or
http://www.motosportsfactory.com/esh...MID_COVERS.htm
#3083
06-15-2011, 12:05 AM
Intermediate
Join Date: Aug 2010
Location: SanClemente CA
Posts: 46
Likes: 0
Received 0 Likes
on
0 Posts
[/IMG]
#3084
06-15-2011, 12:05 AM
Intermediate
Join Date: Aug 2010
Location: SanClemente CA
Posts: 46
Likes: 0
Received 0 Likes
on
0 Posts
#3085
06-15-2011, 12:20 AM
Cruiser
Join Date: Jan 2011
Location: Pacific Northwest
Posts: 123
Likes: 0
Received 0 Likes
on
0 Posts
#3089
06-15-2011, 09:54 AM
Tourer
I would assume that those are either Road King or Street Glide bags mounted on the cycle visions bag mounts.
I would like to see it from the rear, I actually bought a set of bags and mounts exactly like this, with the fillers. Just waiting on the mounts from another HDF member and the bags to be painted. Should be ready the first or second week of July.
I paid 400 for a brand new set of Street Glide bags with all hardware and locks from a hookup from a friend that no longer needed them, 150 to have them sprayed in vivid black and 200 for the mounts and fillers from another member. Total cost for everything was 750.
I am glad I got to see another lo with this done, makes me want mine done even more.
I would like to see it from the rear, I actually bought a set of bags and mounts exactly like this, with the fillers. Just waiting on the mounts from another HDF member and the bags to be painted. Should be ready the first or second week of July.
I paid 400 for a brand new set of Street Glide bags with all hardware and locks from a hookup from a friend that no longer needed them, 150 to have them sprayed in vivid black and 200 for the mounts and fillers from another member. Total cost for everything was 750.
I am glad I got to see another lo with this done, makes me want mine done even more.
Last edited by Lawleywood; 06-15-2011 at 09:59 AM.
#3090
06-15-2011, 10:41 AM
6th Gear
Join Date: Jun 2010
Location: California
Posts: 13
Likes: 0
Received 0 Likes
on
0 Posts
All you need is a paperclip to poke in the hole to release the wires from the harness.
I have the Wild1Chubby WO501 Drag Bar with 8" rise, 30 1/2" wide, 8 1/2" center, and 11 1/2" pullback.
I needed a longer brake line and hand control wires. Clutch and Throttle were fine. Although, I did eventually switch them all out to the HD Black Diamond cables.
I installed the bars myself and it was a pain in the *** getting the wires inside the bars, PATIENCE is a must. I stopped several times, walked away then came back to it. Now I know why they charge so much for this.
I have the Wild1Chubby WO501 Drag Bar with 8" rise, 30 1/2" wide, 8 1/2" center, and 11 1/2" pullback.
I needed a longer brake line and hand control wires. Clutch and Throttle were fine. Although, I did eventually switch them all out to the HD Black Diamond cables.
I installed the bars myself and it was a pain in the *** getting the wires inside the bars, PATIENCE is a must. I stopped several times, walked away then came back to it. Now I know why they charge so much for this.
