Grab rail for Heritage Softail
#1
04-22-2008 | 08:19 AM
Thread Starter
|
6th Gear
Joined: Nov 2007
Posts: 11
Likes: 0
From:
#2
04-23-2008 | 12:22 AM
Road Master
Joined: Sep 2007
Posts: 750
Likes: 6
From: South Florida
RE: Grab rail for Heritage Softail
This Is All I Know
And It Does Fit The 2000 To 2006 Heritage Classic, But With This V-rail You Can't
Put On A Back Rest Pad, If You Want The Pad Then Your Going To Have To Put On A Springer Seat And Drill 2 Holes On Your Fender, It's A Hard Mix But It Does Work, I Ride SOLO So I don't Need The Two Up Buddy Seat, The BottemTwo Picture Is My Bike With The Springer Set Up On It
Good Luck
Harley03joe
The One From V-TWIN Bolts To Your Upper Rear Fender Struts
And It Does Fit The 2000 To 2006 Heritage Classic, But With This V-rail You Can't
Put On A Back Rest Pad, If You Want The Pad Then Your Going To Have To Put On A Springer Seat And Drill 2 Holes On Your Fender, It's A Hard Mix But It Does Work, I Ride SOLO So I don't Need The Two Up Buddy Seat, The BottemTwo Picture Is My Bike With The Springer Set Up On It
Good Luck
Harley03joe
The One From V-TWIN Bolts To Your Upper Rear Fender Struts
#3
04-23-2008 | 07:51 AM
Road Master
Joined: Jan 2007
Posts: 1,226
Likes: 0
#6
04-24-2008 | 01:49 PM
Road Master
Joined: Sep 2007
Posts: 750
Likes: 6
From: South Florida
RE: Grab rail for Heritage Softail
Why Thank You mcpastor [8D]
Your Very Welcome Kizthewize,, What Are You Going To Get ?The V-Rail From V-Twin
Or The Springer Seat ?? Let Me Know Ok
My E-mail is >>>Jjvjjv@aol.com
Your Very Welcome Kizthewize,, What Are You Going To Get ?The V-Rail From V-Twin
Or The Springer Seat ?? Let Me Know Ok
My E-mail is >>>Jjvjjv@aol.com
#7
04-24-2008 | 02:08 PM
Road Master
Joined: Sep 2007
Posts: 750
Likes: 6
From: South Florida
RE: Grab rail for Heritage Softail
I Got My New Springer Seat, Fender Bracket, Got It From www.Surdyke.com The Seat With The V-Rail Was Only $347.00, The Tall And Low Back Rest I Got On E-bay $47.00 Each And I Put The Chrome Spots On Them And Made Up A 100th Emblem For The Seat And Bags
So It All Worked Out A-OK. Just Had To Drill Two Holes In My Fender , I Used A UNI BIT And A Dremel with a Diamond bit To Make The Right Side Hole Ovel , And Was Careful Not To Drill Tru The Wires That Run Down The Right Side Of The Rear Fender, The Painted The Holes Silver, Its Just Like Factory Now, And The Heritage & The Springer Fenders Are The Same
One Might Say I Made It My Own
So It All Worked Out A-OK. Just Had To Drill Two Holes In My Fender , I Used A UNI BIT And A Dremel with a Diamond bit To Make The Right Side Hole Ovel , And Was Careful Not To Drill Tru The Wires That Run Down The Right Side Of The Rear Fender, The Painted The Holes Silver, Its Just Like Factory Now, And The Heritage & The Springer Fenders Are The Same
One Might Say I Made It My Own
ORIGINAL: Dinger
You will need to start with a springer or deluxe seat.
If you're planning on this change, do it soon as the rail and rider's backrest pads are obolete and most dealers won't have them in stock.
You will need to start with a springer or deluxe seat.
If you're planning on this change, do it soon as the rail and rider's backrest pads are obolete and most dealers won't have them in stock.
Trending Topics
#8
02-10-2015 | 11:21 AM
Tourer
Joined: Mar 2008
Posts: 372
Likes: 0
From: east of albany, ny
#9
02-10-2015 | 02:51 PM
Do you have a part # for that seat/backrest? I can't seem to find it on their site. Thanks
I Got My New Springer Seat, Fender Bracket, Got It From www.Surdyke.com The Seat With The V-Rail Was Only $347.00, The Tall And Low Back Rest I Got On E-bay $47.00 Each And I Put The Chrome Spots On Them And Made Up A 100th Emblem For The Seat And Bags
So It All Worked Out A-OK. Just Had To Drill Two Holes In My Fender , I Used A UNI BIT And A Dremel with a Diamond bit To Make The Right Side Hole Ovel , And Was Careful Not To Drill Tru The Wires That Run Down The Right Side Of The Rear Fender, The Painted The Holes Silver, Its Just Like Factory Now, And The Heritage & The Springer Fenders Are The Same
One Might Say I Made It My Own
So It All Worked Out A-OK. Just Had To Drill Two Holes In My Fender , I Used A UNI BIT And A Dremel with a Diamond bit To Make The Right Side Hole Ovel , And Was Careful Not To Drill Tru The Wires That Run Down The Right Side Of The Rear Fender, The Painted The Holes Silver, Its Just Like Factory Now, And The Heritage & The Springer Fenders Are The Same
One Might Say I Made It My Own
