Ignition/Tuner/ECM/Fuel Injection Need advice on ignition issues? Questions about a tuner? Have questions about a EFI calibration or Fuel Injection? Tips on Engine Diagnostics, how to get codes, and what they mean. Find your answers here.

spedo/blinker/running problem

Thread Tools
 
Search this Thread
 
  #1  
Old 08-29-2011, 02:12 PM
dixie FLSTS's Avatar
dixie FLSTS
dixie FLSTS is offline
Cruiser
Thread Starter
Join Date: Oct 2009
Location: south Georgia
Posts: 148
Likes: 0
Received 0 Likes on 0 Posts
Default spedo/blinker/running problem

Had a little problem over the weekend.

My bike is a 2002 FI softail with no motor work.

While on a ride the speedo needle froze up and the OD went blank.
The next time I used the blinker it would not turn off.
Then when stopping at an intersection the bike would sometime go dead.

The whole cycle of the above events went on and off all weekend.

I pulled the Speedo sensor on the top of the trans and cleaned it but that did not help. MY next step is going to be to replace the spedo sensor unless I hear anything different here.

Anyone here have an idea of whats up?

THanks in advance.
 

Last edited by dixie FLSTS; 08-29-2011 at 02:22 PM.
  #2  
Old 08-29-2011, 02:39 PM
UltraNutZ's Avatar
UltraNutZ
UltraNutZ is offline
Extreme HDF Member
Join Date: Nov 2007
Location: East of the Sun, West of the Moon
Posts: 14,673
Received 138 Likes on 109 Posts
Default

might want to take a look at the connector where it plugs into the ECM. pull the plug off, make sure no corrosion is present or pins have come loose. before you plug it back in, make sure to put dielectric grease in the connector.
 
  #3  
Old 09-23-2011, 02:10 PM
dixie FLSTS's Avatar
dixie FLSTS
dixie FLSTS is offline
Cruiser
Thread Starter
Join Date: Oct 2009
Location: south Georgia
Posts: 148
Likes: 0
Received 0 Likes on 0 Posts
Default

bump for any more opinions.
 
  #4  
Old 09-23-2011, 04:59 PM
UltraNutZ's Avatar
UltraNutZ
UltraNutZ is offline
Extreme HDF Member
Join Date: Nov 2007
Location: East of the Sun, West of the Moon
Posts: 14,673
Received 138 Likes on 109 Posts
Default

speedo sensor won't make your ride die so it sounds like a couple of different problems. Pull the crank position sensor and clean it.
 
  #5  
Old 09-23-2011, 07:13 PM
Blk and Chrome's Avatar
Blk and Chrome
Blk and Chrome is offline
Elite HDF Member
Join Date: Jun 2008
Location: Connecticut
Posts: 4,109
Received 8 Likes on 8 Posts
Default

if the speed sensor fails your signals won't cancel, the speedo drops to 0 and at idle the iac won't keep the bike running (stalls). mine went bad and did all the above when it happens stop cycle the ing and see if everything starts working again.
 
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
cc_Penguin
Touring Models
4
06-11-2021 01:10 PM
00copglide
Touring Models
13
08-09-2015 11:55 AM
drs0413
Electrical/Lighting/Alarm
11
05-12-2012 01:01 PM
eshayne
General Topics/Tech Tips
1
05-05-2009 07:47 PM
rking2000
Touring Models
2
10-14-2007 05:44 PM



Quick Reply: spedo/blinker/running problem



All times are GMT -5. The time now is 09:18 AM.