Did HD change the TSM/TSSM marry ?
#1
#2
Join Date: Feb 2007
Location: on the mud flats on the edge of slum city
Posts: 704
Likes: 0
Received 22 Likes
on
22 Posts
I just read the 09 Electrical Diagnostic Manual and it appears to be the same as previous years for the password learn.
The fobs have to be programmed at the dealer with the DT2 though.
You do have the run switch set to RUN and you did try to start it once?
If you miss a step it won't work.
The fobs have to be programmed at the dealer with the DT2 though.
You do have the run switch set to RUN and you did try to start it once?
If you miss a step it won't work.
#3
Switch set to RUN and it started and died just like it was supposed to. Waited 15 minutes for the security light to go off and it never did. I have tried several times and never get passed the first security light going off.
BTW-my fob is not a button fob-just a disk. Does that need programmed prior to the TSSM marry ?
BTW-my fob is not a button fob-just a disk. Does that need programmed prior to the TSSM marry ?
#4
Join Date: Feb 2007
Location: on the mud flats on the edge of slum city
Posts: 704
Likes: 0
Received 22 Likes
on
22 Posts
Yes the fob must be programmed at the dealers.
From the 2009 EDM
Ignition must be off for at least 15 seconds.
Install TSM/HFSM or ECM
Set engine stop switch to RUN
Turn ignition switch to ignition
Wait for engine and security lights to illuminate and then go out
Attempt normal start one time
Engine should start then stall and engine light should illuminate and stay on
Wait ten seconds then security lamp should illuminate
Wait for security lamp to go out (1o minutes)
Then turn ignition to off and back to ignition within one second
Security lamp should illuminate and wait for it to go out (10 minutes)
Then turn ignition to off and back to ignition within one second
Security lamp should illuminate and wait for it to go out (10 minutes)
Then turn ignition to off and back to ignition within one second
Then turn ignition switch to off for at least 15 seconds and then turn on and start bike.
See how you go with that but I would put the original TSM back in clear all codes and start again if I was you.
From the 2009 EDM
Ignition must be off for at least 15 seconds.
Install TSM/HFSM or ECM
Set engine stop switch to RUN
Turn ignition switch to ignition
Wait for engine and security lights to illuminate and then go out
Attempt normal start one time
Engine should start then stall and engine light should illuminate and stay on
Wait ten seconds then security lamp should illuminate
Wait for security lamp to go out (1o minutes)
Then turn ignition to off and back to ignition within one second
Security lamp should illuminate and wait for it to go out (10 minutes)
Then turn ignition to off and back to ignition within one second
Security lamp should illuminate and wait for it to go out (10 minutes)
Then turn ignition to off and back to ignition within one second
Then turn ignition switch to off for at least 15 seconds and then turn on and start bike.
See how you go with that but I would put the original TSM back in clear all codes and start again if I was you.
#5
#6
Yes the fob must be programmed at the dealers.
From the 2009 EDM
Ignition must be off for at least 15 seconds.
Install TSM/HFSM or ECM
Set engine stop switch to RUN
Turn ignition switch to ignition
Wait for engine and security lights to illuminate and then go out
Attempt normal start one time
Engine should start then stall and engine light should illuminate and stay on
Wait ten seconds then security lamp should illuminate
Wait for security lamp to go out (1o minutes)
Then turn ignition to off and back to ignition within one second
Security lamp should illuminate and wait for it to go out (10 minutes)
Then turn ignition to off and back to ignition within one second
Security lamp should illuminate and wait for it to go out (10 minutes)
Then turn ignition to off and back to ignition within one second
Then turn ignition switch to off for at least 15 seconds and then turn on and start bike.
See how you go with that but I would put the original TSM back in clear all codes and start again if I was you.
From the 2009 EDM
Ignition must be off for at least 15 seconds.
Install TSM/HFSM or ECM
Set engine stop switch to RUN
Turn ignition switch to ignition
Wait for engine and security lights to illuminate and then go out
Attempt normal start one time
Engine should start then stall and engine light should illuminate and stay on
Wait ten seconds then security lamp should illuminate
Wait for security lamp to go out (1o minutes)
Then turn ignition to off and back to ignition within one second
Security lamp should illuminate and wait for it to go out (10 minutes)
Then turn ignition to off and back to ignition within one second
Security lamp should illuminate and wait for it to go out (10 minutes)
Then turn ignition to off and back to ignition within one second
Then turn ignition switch to off for at least 15 seconds and then turn on and start bike.
See how you go with that but I would put the original TSM back in clear all codes and start again if I was you.
I used these instructions this afternoon to marry a new security module on my bike.
Followed them step-by step, the bike started fine on first try.
(Next week I'll have the dealer program it for my FOBs.)
-stef
#7
Yes the fob must be programmed at the dealers.
From the 2009 EDM
Ignition must be off for at least 15 seconds.
Install TSM/HFSM or ECM
Set engine stop switch to RUN
Turn ignition switch to ignition
Wait for engine and security lights to illuminate and then go out
Attempt normal start one time
Engine should start then stall and engine light should illuminate and stay on
Wait ten seconds then security lamp should illuminate
Wait for security lamp to go out (1o minutes)
Then turn ignition to off and back to ignition within one second
Security lamp should illuminate and wait for it to go out (10 minutes)
Then turn ignition to off and back to ignition within one second
Security lamp should illuminate and wait for it to go out (10 minutes)
Then turn ignition to off and back to ignition within one second
Then turn ignition switch to off for at least 15 seconds and then turn on and start bike.
See how you go with that but I would put the original TSM back in clear all codes and start again if I was you.
From the 2009 EDM
Ignition must be off for at least 15 seconds.
Install TSM/HFSM or ECM
Set engine stop switch to RUN
Turn ignition switch to ignition
Wait for engine and security lights to illuminate and then go out
Attempt normal start one time
Engine should start then stall and engine light should illuminate and stay on
Wait ten seconds then security lamp should illuminate
Wait for security lamp to go out (1o minutes)
Then turn ignition to off and back to ignition within one second
Security lamp should illuminate and wait for it to go out (10 minutes)
Then turn ignition to off and back to ignition within one second
Security lamp should illuminate and wait for it to go out (10 minutes)
Then turn ignition to off and back to ignition within one second
Then turn ignition switch to off for at least 15 seconds and then turn on and start bike.
See how you go with that but I would put the original TSM back in clear all codes and start again if I was you.
Trending Topics
#8
Yes the fob must be programmed at the dealers.
From the 2009 EDM
Ignition must be off for at least 15 seconds.
Install TSM/HFSM or ECM
Set engine stop switch to RUN
Turn ignition switch to ignition
Wait for engine and security lights to illuminate and then go out
Attempt normal start one time
Engine should start then stall and engine light should illuminate and stay on
Wait ten seconds then security lamp should illuminate
Wait for security lamp to go out (1o minutes)
Then turn ignition to off and back to ignition within one second
Security lamp should illuminate and wait for it to go out (10 minutes)
Then turn ignition to off and back to ignition within one second
Security lamp should illuminate and wait for it to go out (10 minutes)
Then turn ignition to off and back to ignition within one second
Then turn ignition switch to off for at least 15 seconds and then turn on and start bike.
See how you go with that but I would put the original TSM back in clear all codes and start again if I was you.
From the 2009 EDM
Ignition must be off for at least 15 seconds.
Install TSM/HFSM or ECM
Set engine stop switch to RUN
Turn ignition switch to ignition
Wait for engine and security lights to illuminate and then go out
Attempt normal start one time
Engine should start then stall and engine light should illuminate and stay on
Wait ten seconds then security lamp should illuminate
Wait for security lamp to go out (1o minutes)
Then turn ignition to off and back to ignition within one second
Security lamp should illuminate and wait for it to go out (10 minutes)
Then turn ignition to off and back to ignition within one second
Security lamp should illuminate and wait for it to go out (10 minutes)
Then turn ignition to off and back to ignition within one second
Then turn ignition switch to off for at least 15 seconds and then turn on and start bike.
See how you go with that but I would put the original TSM back in clear all codes and start again if I was you.
Thanks
#10