TTS Mastertune Information
#6811
#6813
Quick answer
See the box on the right hand bottom of datamaster? (engine speed and MAP.....)
Double click on any setting and change it to Knock Retard front and another to back.
It will show you knock if you have one.
It is best to get rid of everything else but Knock so it is easy to see.
See the box on the right hand bottom of datamaster? (engine speed and MAP.....)
Double click on any setting and change it to Knock Retard front and another to back.
It will show you knock if you have one.
It is best to get rid of everything else but Knock so it is easy to see.
The following users liked this post:
Pamartin7 (06-24-2017)
#6814
#6816
What's right for your motor may not be right for each motor this is another reason why the TTS software was written to be easy yet so smart. Let the software do it's thing and lead you. Do not over think things.
If a max of -1 is normal for you motor then it is normal.
Remember... TTS will only decrease timing. It will not increase when VTuning. So if you want to increase your timing a few degrees before VTuning then do so and the TTS software will make corrections.
Always tune with fresh plugs, gas and a clean air filter. For getting high load areas take a friend for extra weight.
#6817
That makes sense. I am just getting an occasional noise at idle and I can't figure out why it's doing it. I am trying my best but I can't tell if there is anything that needs addressing from a generic 02 reading.
https://app.box.com/s/ejcx48ohwgeffeys2und68kwc84gui3a - Here is the recording if that helps.
https://app.box.com/s/ejcx48ohwgeffeys2und68kwc84gui3a - Here is the recording if that helps.
#6818
Thanks for the advice.
I converted the last file that I uploaded to the ECM years ago and attempted to upload it to the ECM today and got the same error message as before, then I tried to upload the latest CAE176 MT8 to the ECM and got the same error.
I was able the download the installed ETM file, but when I attempt to open it I get a message that the file type is unsupported.
I'm thinking of uninstalling everything and starting fresh - do you think this might help?
I converted the last file that I uploaded to the ECM years ago and attempted to upload it to the ECM today and got the same error message as before, then I tried to upload the latest CAE176 MT8 to the ECM and got the same error.
I was able the download the installed ETM file, but when I attempt to open it I get a message that the file type is unsupported.
I'm thinking of uninstalling everything and starting fresh - do you think this might help?
Last edited by 1004ron; 06-26-2017 at 08:23 PM.
#6819
Thanks for the advice.
I converted the last file that I uploaded to the ECM years ago and attempted to upload it to the ECM today and got the same error message as before, then I tried to upload the latest CAE176 MT8 to the ECM and got the same error.
I was able the download the installed ETM file, but when I attempt to open it I get a message that the file type is unsupported.
I'm thinking of uninstalling everything and starting fresh - do you think this might help?
I converted the last file that I uploaded to the ECM years ago and attempted to upload it to the ECM today and got the same error message as before, then I tried to upload the latest CAE176 MT8 to the ECM and got the same error.
I was able the download the installed ETM file, but when I attempt to open it I get a message that the file type is unsupported.
I'm thinking of uninstalling everything and starting fresh - do you think this might help?
#6820
It is after doing just that (software and firmware updates) that I'm encountering these problems.
Last edited by 1004ron; 06-27-2017 at 08:22 PM.