TTS Mastertune Information
#2591
#2592
sounds like you figured out how to save your original ecm calibration (stock one) you really do need to do the camanalyzer. It has been a while since I did mine but I think it is ok if the afr's stay yellow to get the cam data.
#2593
THis is what Doc at TTS just sent me
You do not have to mess with the cam settings....you can leave them alone. That is for big builds with high lift cams that are a lot different than the SE cams. If the cam is stock leave the cam selector alone.
Up date your tuning guide and you can read about the cam selector.
Yes set the afr table to 14.6 every where it will do so.....set the PE to 10000, turn off the accel table and the decel table, turn off the warm-up enrichment table and set the bias voltage to .760 or close......this is for the best results. After your finished turn every thing back to ORGINAL except the Bias Voltage table....let it at .760 or close.
Doc
You do not have to mess with the cam settings....you can leave them alone. That is for big builds with high lift cams that are a lot different than the SE cams. If the cam is stock leave the cam selector alone.
Up date your tuning guide and you can read about the cam selector.
Yes set the afr table to 14.6 every where it will do so.....set the PE to 10000, turn off the accel table and the decel table, turn off the warm-up enrichment table and set the bias voltage to .760 or close......this is for the best results. After your finished turn every thing back to ORGINAL except the Bias Voltage table....let it at .760 or close.
Doc
#2594
#2595
Wiz i wish i had you. You keep coming on and off. So far you have been a big help getting me to understand. I will stand by till your back on.
Where is bias voltage table, accel and decel table, warmup enrichment table. I see in table selection these but there is no where to disable them.
Where is bias voltage table, accel and decel table, warmup enrichment table. I see in table selection these but there is no where to disable them.
#2596
THis is what Doc at TTS just sent me
You do not have to mess with the cam settings....you can leave them alone. That is for big builds with high lift cams that are a lot different than the SE cams. If the cam is stock leave the cam selector alone.
Up date your tuning guide and you can read about the cam selector.
Yes set the afr table to 14.6 every where it will do so.....set the PE to 10000, turn off the accel table and the decel table, turn off the warm-up enrichment table and set the bias voltage to .760 or close......this is for the best results. After your finished turn every thing back to ORGINAL except the Bias Voltage table....let it at .760 or close.
Doc
You do not have to mess with the cam settings....you can leave them alone. That is for big builds with high lift cams that are a lot different than the SE cams. If the cam is stock leave the cam selector alone.
Up date your tuning guide and you can read about the cam selector.
Yes set the afr table to 14.6 every where it will do so.....set the PE to 10000, turn off the accel table and the decel table, turn off the warm-up enrichment table and set the bias voltage to .760 or close......this is for the best results. After your finished turn every thing back to ORGINAL except the Bias Voltage table....let it at .760 or close.
Doc
#2597
#2598
Not to be harsh, but have you read the tuning guide? The clb table doesn't get disabled. Highlight the cells and set them to 759 or number of your choice. Warmup enrichment can be left as is. I zero it out on the dyno so I don't have to wait for it to decay to zero, as it is a time based table. Just saves me time. On the street you don't need to do it. The AE &DE tables get set to zero.
#2600
Not to be harsh, but have you read the tuning guide? The clb table doesn't get disabled. Highlight the cells and set them to 759 or number of your choice. Warmup enrichment can be left as is. I zero it out on the dyno so I don't have to wait for it to decay to zero, as it is a time based table. Just saves me time. On the street you don't need to do it. The AE &DE tables get set to zero.
Then warmup enrichment change all cells to 0. This is what Doc means by turn it off, by changing them to 0. I figured there would be something to click saying enable or disable.