Harley Davidson Forums

General Harley Davidson Chat Forum to discuss general Harley Davidson issues, topics, and experiences.
Sponsored by:
Sponsored by:

UPDATED - How To: Diagnostic Trouble Codes (DTC's)

Thread Tools
 
Search this Thread
 
  #21  
Old 09-21-2009, 07:36 PM
cHarley's Avatar
cHarley
cHarley is offline
Club Member
Thread Starter
Join Date: Feb 2007
Location: Boynton Beach, FloriDuh
Posts: 16,320
Received 302 Likes on 231 Posts
Default
Originally Posted by genedjr
I have this exact thing. And after searching I see that this means the diagnostic code 1 is clear.

Should I assump that if no codes are sent that you don't see the 'diag' initial screen on the speedo?

...gene
Originally Posted by mater r-130
When i push the button and then turn on the switch the speedo does nothing, no sweeping action. The word diag does not appear?. what i do get is do1clr and when you push the button it goes to the samething do2clr and so on to do10clr, I push it one more time and it says cal 03. What does this mean?.

Sorry, but the above DTC list and procedure applies to newer model ICM/ECM bikes, starting in I believe 2004.
 
Reply Like
  #22  
Old 11-08-2009, 09:55 AM
sahara38's Avatar
sahara38
sahara38 is offline
Advanced
Join Date: Dec 2006
Location:
Posts: 59
Likes: 0
Received 0 Likes on 0 Posts
Thumbs up
cHarley...thanks for the info here. I've got the pdf saved to my computer for future reference. Very helpful.
 
Reply Like
  #23  
Old 03-08-2010, 05:11 PM
RoadKing904's Avatar
RoadKing904
RoadKing904 is offline
Novice
Join Date: May 2009
Location: St Augustine, Fl
Posts: 23
Received 0 Likes on 0 Posts
Default
I have a 99 FLHRCI and have the older diagnostic codes and the last position is Cal 03 - does anyone have the translation of the 10 diagnostic codes?
Appreciate everyone's input.
 
Reply Like
  #24  
Old 03-18-2010, 01:10 PM
wideglidewy's Avatar
wideglidewy
wideglidewy is offline
Intermediate
Join Date: Mar 2010
Posts: 31
Likes: 0
Received 0 Likes on 0 Posts
Default
Hi - gread thread. I have a dead '04 FXDWG - will turn over but no spark. Suspected bad ICM. Ran diagnostic and the code was "no rsp" - does this mean a short, dead ICM, or both? Thanks in advance.
 
Reply Like
  #25  
Old 03-18-2010, 01:29 PM
cHarley's Avatar
cHarley
cHarley is offline
Club Member
Thread Starter
Join Date: Feb 2007
Location: Boynton Beach, FloriDuh
Posts: 16,320
Received 302 Likes on 231 Posts
Default
Originally Posted by wideglidewy
Hi - gread thread. I have a dead '04 FXDWG - will turn over but no spark. Suspected bad ICM. Ran diagnostic and the code was "no rsp" - does this mean a short, dead ICM, or both? Thanks in advance.
You might want to thoroughly reread the OP to make sure you are checking all groups of codes.

This is in the OP instructions:
"On models not equipped with a tachometer "No Rsp" will appear when the tachometer identifier is selected."
"No Rsp" will also appear if the run/off switch is in the off position when doing this procedure."
 
Last edited by cHarley; 03-18-2010 at 01:31 PM.
Reply Like
  #26  
Old 03-22-2010, 12:52 PM
clarkchriston's Avatar
clarkchriston
clarkchriston is offline
Road Master
Join Date: Mar 2008
Location: Puyallup, WA
Posts: 855
Likes: 0
Received 1 Like on 1 Post
Default
Thanks for the info. Hopefully I will never need it but we all know that's highly unlikely.
 
Reply Like
  #27  
Old 03-22-2010, 02:39 PM
FXDXTSport's Avatar
FXDXTSport
FXDXTSport is offline
Stellar HDF Member
Join Date: Oct 2006
Location: Washington State
Posts: 2,538
Received 541 Likes on 241 Posts
Default
Originally Posted by cHarley
Sorry, but the above DTC list and procedure applies to newer model ICM/ECM bikes, starting in I believe 2004.
Three pages in and I find out it doesen't apply to my bike What a useless post JUST KIDDING I think this might be the most informative post I've seen on this forum if you have an 04 to 08 bike.
 
Reply Like
  #28  
Old 03-26-2010, 06:54 PM
masterblaster's Avatar
masterblaster
masterblaster is offline
Ultimate HDF Member
Join Date: Dec 2006
Location: Conroe Texas
Posts: 8,961
Received 258 Likes on 100 Posts
Default
Thanks Charley, I just figured out my ECU, a newley installed Thundermax is not responding, wasted a whole day trying to figure why the dam computer would not link, even went and bought a different usb sserial adaptor.

Great thread.
 
Reply Like
  #29  
Old 03-27-2010, 07:02 AM
silverwolf79's Avatar
silverwolf79
silverwolf79 is offline
Outstanding HDF Member
Join Date: May 2009
Location: Bedford Co. Pa .
Posts: 2,608
Likes: 0
Received 2 Likes on 2 Posts
Default
Thanks Guys , excellent post !
 
Reply Like
  #30  
Old 04-30-2010, 10:42 AM
Just Plain Cody's Avatar
Just Plain Cody
Just Plain Cody is offline
Intermediate
Join Date: Apr 2010
Location: Charlotte, NC
Posts: 34
Likes: 0
Received 0 Likes on 0 Posts
Default
What does it mean when the speedo digital display says "no CAL" and Speedo does Not go in to diag mode at all? This is on an 07 XL1200C. This code ('no CAL') is not mentioned in this thread.
 
Last edited by Just Plain Cody; 05-01-2010 at 01:52 PM.
Reply Like



Advanced Search
Quick Reply: UPDATED - How To: Diagnostic Trouble Codes (DTC's)


Reply Closed Thread Share
Forum Jump

All times are GMT -5. The time now is 01:31 AM.