Dyna Defender Parts Locator?
#21
12-12-2011, 04:59 AM
Join Date: Feb 2007
Location: Harmelen (The Netherlands, Europe)
Posts: 9,002
Received 876 Likes
on
584 Posts
...My Defender has no brake lights at all. I suspect the brake light switch on the rear master is bad but I am having difficulty obtaining another as the sources I have been using for parts indicate the stop light switch on this model is obsolete/no longer available (same on FXDX). Do you know if it's likely a switch off a Sportster or a bagger might fit an '04 Defender application? Any possibililty they are all the same?
#23
12-12-2011, 07:48 AM
Road Master
#24
12-14-2011, 07:28 PM
To the best of my knowledge and belief, my bike has the original, stock H-D handlebars that came on the bike when it was purchased new by the El Paso PD. This based on the info I was able to glean from the guy who bought this bike & others from EPPD at auction last July. However, I cannot be absolutely sure.
In any case, per Rene request, the measurements I made of the bars on my Defender are depicted below. Hope this is of some use
Last edited by M&P340; 12-14-2011 at 07:39 PM. Reason: Left off Base Width measurement in original dwg
#25
12-14-2011, 07:44 PM
Road Master
Thank you to Rene for making the request. Thank you JLF for the work getting the specs. Do you know the O.D. of the bars? 28" width...I think not a lot of leverage compared to the 32.5" stock bars. I suppose because of it's job being 'on the street' and not so much at highway speeds.
I very much appreciate the time and info. Thank you!
Dave
I very much appreciate the time and info. Thank you!
Dave
#26
12-14-2011, 07:52 PM
Thank you to Rene for making the request. Thank you JLF for the work getting the specs. Do you know the O.D. of the bars? 28" width...I think not a lot of leverage compared to the 32.5" stock bars. I suppose because of it's job being 'on the street' and not so much at highway speeds.
I very much appreciate the time and info. Thank you!
Dave
I very much appreciate the time and info. Thank you!
Dave
Yes, Dave. The bars are 1" O.D.
Yes, I would say you are correct on the leverage issue. My experience is limited, but in the short time I've ridden it (it's torn apart now for restoration), I was struck by how minimal the leverage is with these bars. But then again, I'm used to very WIDE dirt bike bars.
#27
06-12-2020, 06:28 PM
Engine guard
p/n 29158-99 AIR CLEANER INSERT, POLICE
Available at Latus...
I have the 2004 FXDP parts catalog. If you need any p/n's just shoot me a PM and I'll check them for you!
Sometimes Ebay has auctions for FXDP parts. Another source could be Vintage Parts
Available at Latus...
I have the 2004 FXDP parts catalog. If you need any p/n's just shoot me a PM and I'll check them for you!
Sometimes Ebay has auctions for FXDP parts. Another source could be Vintage Parts
#28
06-12-2020, 07:01 PM
Club Member
49009-03 Engine Guard
Besides the Online Parts Finder where you can get those numbers, Here's the 2004 FXDP Factory Parts Catalog that you can download if you want ... RIGHT HERE
Besides the Online Parts Finder where you can get those numbers, Here's the 2004 FXDP Factory Parts Catalog that you can download if you want ... RIGHT HERE
#29
06-12-2020, 11:01 PM
I JUST sold one a couple weeks ago. I was trying to accommodate lowers and they didn’t work with the engine guard. I sold the Defender floorboards, shifter and brake pedal and went back to stock mids with a “regular” Dyna engine guard and the lowers worked fine.