Let's keep track of our Superglide Mods
#51
Was wondering what size and brand the bars are on this FXDC? They fit the bike really well and am looking for something similar....
Thanks
Jamie
Thanks
Jamie
09 FXDC,
List of mods
Screamin Eagle intake
2in tank lift
Hooker Trouble Makers
PC-V
Black braided cables
Dyno Tuned by BG Harley
Smoothed rear fender
LED tail/turn signals
Moved front turn signals
LePera solo seat
Avon edge cut grips and pegs (no new pictures since installed)
11in Progressive shocks
front end lowered 1in
And after my July vacation RC Czar Eclipse wheels
List of mods
Screamin Eagle intake
2in tank lift
Hooker Trouble Makers
PC-V
Black braided cables
Dyno Tuned by BG Harley
Smoothed rear fender
LED tail/turn signals
Moved front turn signals
LePera solo seat
Avon edge cut grips and pegs (no new pictures since installed)
11in Progressive shocks
front end lowered 1in
And after my July vacation RC Czar Eclipse wheels
#52
#53
OutlawBagger - That fender looks real clean. I like!
Wasn't going to post my stuff on here as I have a recent winter mods thread going but...
Chrome Harley Switchblade Wheels
V&H Propipe
SEST
Ness BigSucker
StreetBob bars w/flipped mirrors
Signal relocate
Re-covered Seat
Wasn't going to post my stuff on here as I have a recent winter mods thread going but...
Chrome Harley Switchblade Wheels
V&H Propipe
SEST
Ness BigSucker
StreetBob bars w/flipped mirrors
Signal relocate
Re-covered Seat
Last edited by fella; 02-15-2012 at 12:35 PM.
#54
2011 fxdc
Here are the list of mods!
-Street Slammer Bars
-Arlen Ness Mirrors
-VO2 stage one intake
-Vance and Hines Fuelpak
-Vance and Hine 2 into 2 big radius
-LED brake light, not pictured
-Front turn signal relocation
-Lay down license plate with rear turn signals relocated
-Kuryakyn swing wing rider and passenger pegs
-Kuryakyn grips
-Also not pictured, home made detachable saddle bags, detachable windshield.
-Street Slammer Bars
-Arlen Ness Mirrors
-VO2 stage one intake
-Vance and Hines Fuelpak
-Vance and Hine 2 into 2 big radius
-LED brake light, not pictured
-Front turn signal relocation
-Lay down license plate with rear turn signals relocated
-Kuryakyn swing wing rider and passenger pegs
-Kuryakyn grips
-Also not pictured, home made detachable saddle bags, detachable windshield.
#56
Mine - 2007 FXDC
- Bullet headlight w/LED
- 14" Wild 1 chubbies
- Progressive springs up front, 12 ricors in back
- Detachable saddle bag, battery bags, solo side bags most are off
- 2-1 Bassani road rage
- Stage 1, w/ SE air filter
- SE 204 cams
- PCIII
- a bunch of chrome parts
- True Track
- 180 rear tire
- verticle side plate (not shown and dont run the bags)
- integrated turn brake light (removed turn signals front and back)
- wolo air horn (not shown)
- mustang seat with backrest
- detach windshield
- oil cooler
Here in the Philippines, anything goes so am in the process of removing parts.
- Bullet headlight w/LED
- 14" Wild 1 chubbies
- Progressive springs up front, 12 ricors in back
- Detachable saddle bag, battery bags, solo side bags most are off
- 2-1 Bassani road rage
- Stage 1, w/ SE air filter
- SE 204 cams
- PCIII
- a bunch of chrome parts
- True Track
- 180 rear tire
- verticle side plate (not shown and dont run the bags)
- integrated turn brake light (removed turn signals front and back)
- wolo air horn (not shown)
- mustang seat with backrest
- detach windshield
- oil cooler
Here in the Philippines, anything goes so am in the process of removing parts.
Last edited by DonN; 02-15-2012 at 08:03 PM.
#58
Has anyone here installed Handlebars with internal wiring properly without cutting the wires in the handlebar controls?
My SuperGlide buckhorns came with dimples and after reading the service manual. There were 2 ways of doing them.
1. Cut the wires from the handlebar controls
2. Individually take each corresponding wire from the harness. Then reroute from there.
Im guessing option 2 would suck. But my assumptions is that everybody else just cut the wiring and hide it in the controls or run the splices through the bars.
Thanks
My SuperGlide buckhorns came with dimples and after reading the service manual. There were 2 ways of doing them.
1. Cut the wires from the handlebar controls
2. Individually take each corresponding wire from the harness. Then reroute from there.
Im guessing option 2 would suck. But my assumptions is that everybody else just cut the wiring and hide it in the controls or run the splices through the bars.
Thanks
#60
Some great looking mods in this thread! Here's mine
I know mine won't measure up to lots of the bikes in this thread but one thing I keep having to tell myself, it's a personal thing, what looks great to one person might not be what another person has in mind for a great mod. The bike to me is like my piece of artwork, it's not going to be finished until it's done but it will always need that one more thing to make it better, then one more thing, then that last little thing and on and on.....
Thing I love most about the thread are the ideas it gives me for those "one more things" to add! Great way to see how others have done it and see how I can do it but make it unique and unique is always a good thing!
Great luck all, watch out for everyone not watchin out for you and be safe! Mods on mine are listed in the sig.
Thing I love most about the thread are the ideas it gives me for those "one more things" to add! Great way to see how others have done it and see how I can do it but make it unique and unique is always a good thing!
Great luck all, watch out for everyone not watchin out for you and be safe! Mods on mine are listed in the sig.