sparto light removal queston?
#12
I removed mine a while back.....but its is back in place now.....when removed, leaves a big hole in the fender...its not just bolt holes and wiring holes....I bent my license plate around a water pipe on the side of the house and mounted it across the bottom of the fender, covering hole, using the mounting holes for the tail light and plate bracket. Also the turn signals will continue to function as brake/turn signals when the tail light is removed with no issue.....
#13
Here's a good thread of reference:
https://www.hdforums.com/forum/dyna-...ar-fender.html
I know that when you disconnect the tail light and remove it, there will be a fairly large hole in the rear fender plus the mounting bolt holes. I've seen some guys take HD medallions and just place them over the hole and then put some kind of decorative bolt in the old bolt holes. There are some pics on the forum somewhere but I couldn't find them quickly. The rear fender looks a little busy this way but it removes the tail light which prevents the fender from cracking.
https://www.hdforums.com/forum/dyna-...ar-fender.html
I know that when you disconnect the tail light and remove it, there will be a fairly large hole in the rear fender plus the mounting bolt holes. I've seen some guys take HD medallions and just place them over the hole and then put some kind of decorative bolt in the old bolt holes. There are some pics on the forum somewhere but I couldn't find them quickly. The rear fender looks a little busy this way but it removes the tail light which prevents the fender from cracking.
#15
oh ...those jigamajangs...got it...in fact I have a couple of assorted packs in my tool box...thanks
#16
What kind of mileage do these cracks normally start happening?
I washed my bike last week and noticed a horizontal line across the license plate. Wiggled it a little and it almost snapped off. Ended up drilling a couple holes through the bottom of it to keep it from breaking all the way off. Now the vibration that caused the plate to crack will probly be transfered to the fender.
I washed my bike last week and noticed a horizontal line across the license plate. Wiggled it a little and it almost snapped off. Ended up drilling a couple holes through the bottom of it to keep it from breaking all the way off. Now the vibration that caused the plate to crack will probly be transfered to the fender.
#17
Man, I have a few post on this subject and they all seem a little disturbing! I am glade I ordered and replaced my rear fender with the Chopped Fender kit from the MoCo, some people say this is an expensive fender upgrade. But, looking at all the problems with the stock set up, I would have to say it was money well spent!
You are able to order the fender buy itself and I believe you can also order it color matched. If you install a side mount plate, you don't need the whole kit because the Street Bob is already set up for the fender, all you have to do is remove the center light wires (reroute the light wire for the tag light and remove or reroute the Brake light if you use a side mount brake light also) and reroute the turn sigs down the inside sides (with strut bracket) of the fender, that is all I did.
You are able to order the fender buy itself and I believe you can also order it color matched. If you install a side mount plate, you don't need the whole kit because the Street Bob is already set up for the fender, all you have to do is remove the center light wires (reroute the light wire for the tag light and remove or reroute the Brake light if you use a side mount brake light also) and reroute the turn sigs down the inside sides (with strut bracket) of the fender, that is all I did.
#18
Man, I have a few post on this subject and they all seem a little disturbing! I am glade I ordered and replaced my rear fender with the Chopped Fender kit from the MoCo, some people say this is an expensive fender upgrade. But, looking at all the problems with the stock set up, I would have to say it was money well spent!
You are able to order the fender buy itself and I believe you can also order it color matched. If you install a side mount plate, you don't need the whole kit because the Street Bob is already set up for the fender, all you have to do is remove the center light wires (reroute the light wire for the tag light and remove or reroute the Brake light if you use a side mount brake light also) and reroute the turn sigs down the inside sides (with strut bracket) of the fender, that is all I did.
You are able to order the fender buy itself and I believe you can also order it color matched. If you install a side mount plate, you don't need the whole kit because the Street Bob is already set up for the fender, all you have to do is remove the center light wires (reroute the light wire for the tag light and remove or reroute the Brake light if you use a side mount brake light also) and reroute the turn sigs down the inside sides (with strut bracket) of the fender, that is all I did.
I like how clean your rear fender looks...very nice...i hope mine will end up like that
#19
ultimately that's what I will end up with (I hope)... I just didn't want to spring for a new fender...I'm hoping that after I receive my new fender from harley, I will have the dealer install the fender without the sparto light and I will have a local body shop fill the holes and repaint...I'm guessing that might be a little less expensive than buying a complete fender...perhaps I'm wrong ...I just wanted a temporary fix until I can get the holes filled ...
I like how clean your rear fender looks...very nice...i hope mine will end up like that
I like how clean your rear fender looks...very nice...i hope mine will end up like that
#20
Here's a thought - if HD is replacing your fender, why not see if the dealer will get you the chopped fender instead of the stock one and just pay the difference. That way you get the fender you want and HD doesn't have to replace another fender should it happen again..........seems like a win-win for everybody.