PCV and 2010 Dynas
#11
I'm getting ready to have a PC5 installed on my 2010 WG. While I was reviewing the installation instructions it appeared that the pin connector is going to be dangling/ exposed outside of the electrical box, somewhere behind the rear cyl. Is this correct and is it not possible to have it connected within the electrical box or somewhere it not exposed and visible? I really don't want to see another big connector just crammed behind the cylinder? I'm scheduled for installation on Sat at the local Dynojet tuner in Santa Maria so would appreciate any comments. Thanks
p.s. I love the C5 Z06 wheels in the background of the pic, they are my all time favorite wheels.
__________________
Jamie Long / Fuel Moto USA
The USA's Leader V-Twin EFI & Performance www.fuelmotousa.com
Contact 920-423-3309
Email jamie@fuelmotousa.com
Jamie Long / Fuel Moto USA
The USA's Leader V-Twin EFI & Performance www.fuelmotousa.com
Contact 920-423-3309
Email jamie@fuelmotousa.com
#12
Thanks Jamie, I appreciate the info as it puts my mind to rest over that issue. Do you mind giving me your opinion regarding the PC5 overall? There is so much differing opinion out there that I would appreciate yours. I will be having the PC5 installed tomorrow by Jeff in Santa Maria, an official Dynojet tuner, using his dyno and installation knowledge. My concern is rather general: is the PC5 the best overall choice for basic hard street riding and good fuel management so the motor doesn't run too lean and hot. Any comments are appreciated.
p.s. I like the wheels but prefer my IForged TE5-S's as they will handle a wider set of PS2's.
p.s. I like the wheels but prefer my IForged TE5-S's as they will handle a wider set of PS2's.
#13
While we are talking about all the advantages, wanted to just to mention here that the problem with using any of the the PCs on the late model bikes is that they simply force the bike into entirely open loop operation which cripples the ECUs capability to adapt to changing fuel quality. The PCs were the ticket years ago in simpler times and may still be fine for making power, if you get the same fuel all the time. But today we seem to have crappy and inconsistent fuel, which may effect one state more than another. The PCs without autotune have no way to sense crappy fuel before potential damage is done.
I dunno, just saying that there are better late model bikes tuning tools that do cost a few dollars more but have also proven to provide a better street tune in practice as well as getting the most out of your fuel from tank to tank (without nearly as much damage risk). Just something to think about. One reason perhaps the PCV people have added the autotune module and O2 sensors to the lineup. These can cope with the changing fuels and make be a benefit once the fuel problems become more well known.
I dunno, just saying that there are better late model bikes tuning tools that do cost a few dollars more but have also proven to provide a better street tune in practice as well as getting the most out of your fuel from tank to tank (without nearly as much damage risk). Just something to think about. One reason perhaps the PCV people have added the autotune module and O2 sensors to the lineup. These can cope with the changing fuels and make be a benefit once the fuel problems become more well known.
#14
I'm getting ready to have a PC5 installed on my 2010 WG. While I was reviewing the installation instructions it appeared that the pin connector is going to be dangling/ exposed outside of the electrical box, somewhere behind the rear cyl. Is this correct and is it not possible to have it connected within the electrical box or somewhere it not exposed and visible? I really don't want to see another big connector just crammed behind the cylinder? I'm scheduled for installation on Sat at the local Dynojet tuner in Santa Maria so would appreciate any comments. Thanks
That location behind the rear cylinder sucks. Dont look good at all.
Thats where i had my PCV connector untill i saw this vid of the fuelpak which uses the same connector. Fits behind the electrical box under the ECU perfect. The connector must be oriented the correct way or the new harness will not reach the ECU. Also, take the battery and battery box off and installation will go much better.
http://www.youtube.com/watch?v=DNuCX...layer_embedded
#16
#17
That location behind the rear cylinder sucks. Dont look good at all.
Thats where i had my PCV connector untill i saw this vid of the fuelpak which uses the same connector. Fits behind the electrical box under the ECU perfect. The connector must be oriented the correct way or the new harness will not reach the ECU. Also, take the battery and battery box off and installation will go much better.
http://www.youtube.com/watch?v=DNuCX...layer_embedded
Thats where i had my PCV connector untill i saw this vid of the fuelpak which uses the same connector. Fits behind the electrical box under the ECU perfect. The connector must be oriented the correct way or the new harness will not reach the ECU. Also, take the battery and battery box off and installation will go much better.
http://www.youtube.com/watch?v=DNuCX...layer_embedded
#18
#19
The PCV is installed and dyno results while not exactly earth shattering are better than stock. According to Cycle World's latest write up on the 2010 Wide Glide the stock Hp is 63 and the torque is 81.1. After PCV installation the dyno read 70.77hp and 84.5 tq. on my WG. So picked up 7 Hp and 3 lbs torque for $500. Installation went OK but i'll need to clean up the wiring a bit. One thing for sure is that it seems to pull stronger and feels smoother but not all that different, it does sound a bit more balanced ??. Not sure what I mean but it sounds better. Thanks again for all the comments and info. The forum is a great source of info.
Thread
Thread Starter
Forum
Replies
Last Post