What did you do to your Dyna today?
I finally got the external breather done. I tried drilling out the rubber tubes that come with the SE intake but they looked like hell when I was done. This is what happens when I drink too much and watch YouTube.
I had better luck this morning. Ace Hardware had some nice grommets their treasure bins and the auto part store had the 90 degree elbows.
I think the edge trim on the football makes it look more stock.
I had better luck this morning. Ace Hardware had some nice grommets their treasure bins and the auto part store had the 90 degree elbows.
I think the edge trim on the football makes it look more stock.
The following 6 users liked this post by Rusty Springs:
CanOfSoup (01-14-2023),
Davdoodles (01-02-2023),
Dynawobble (12-31-2022),
Garage Queen Rescue (12-31-2022),
sbrooks64 (12-31-2022),
and 1 others liked this post.
The following 5 users liked this post by SW CQB 45:
Davdoodles (01-02-2023),
Dynawobble (12-31-2022),
Garage Queen Rescue (01-01-2023),
Jaystn62 (01-02-2023),
Rusty Springs (01-01-2023)
FXRP Fairing & Lowers
Okay. I got the RP fairing and lowers test fit and all holes drilled. Trimmed the fairing some to clear the 49mm tubes and the right side lower to clearance the thunderheader. This fairing was bought used and it had already been trimmed but they did a **** job but that's what you get when you buy used. Paint appointment in 2 weeks. Woooooooot!
The following 2 users liked this post by Dynawobble:
Davdoodles (01-05-2023),
Garage Queen Rescue (01-02-2023)
I finally received my shipment from Hillside Cycle. I will start the install this week and hopefully finish by the weekend.
The following 4 users liked this post by NEWROADSTER:
Dynawobble (01-02-2023),
Garage Queen Rescue (01-02-2023),
Jaystn62 (01-02-2023),
snake_eyes (01-02-2023)
I could stare at that table all day! 😂
The following 2 users liked this post by Dynawobble:
lonbak (01-02-2023),
snake_eyes (01-02-2023)
You will be pleased.. I could tell by the hand writing exactly who that was.. Scott.. I've have a lot of work done by him ..
I would be seriously interested to see what that turns on the dyno.. if you could post those pics of the sheet I would greatly appreciate it. Best cam I ever had was the Woods 8 cam..
I would be seriously interested to see what that turns on the dyno.. if you could post those pics of the sheet I would greatly appreciate it. Best cam I ever had was the Woods 8 cam..
Last edited by 98hotrodfatboy; 01-02-2023 at 12:34 PM.
The following users liked this post:
Dynawobble (01-02-2023)
Thanks for all the support, I am excited to finally get started. I will post updates as I move along. This is not my first engine build but it is my first Harley engine build. I have all the correct tools so hopefully it will go smoothly although, I may have a question or two along the way.
As far as the tuning, Scott recommended Ed at Dyno Difference in Dallas. I will do the first warm ups and then carry the bike to him. I will definitely post what I get. I hope it hammers!
As far as the tuning, Scott recommended Ed at Dyno Difference in Dallas. I will do the first warm ups and then carry the bike to him. I will definitely post what I get. I hope it hammers!
Thanks for all the support, I am excited to finally get started. I will post updates as I move along. This is not my first engine build but it is my first Harley engine build. I have all the correct tools so hopefully it will go smoothly although, I may have a question or two along the way.
As far as the tuning, Scott recommended Ed at Dyno Difference in Dallas. I will do the first warm ups and then carry the bike to him. I will definitely post what I get. I hope it hammers!
As far as the tuning, Scott recommended Ed at Dyno Difference in Dallas. I will do the first warm ups and then carry the bike to him. I will definitely post what I get. I hope it hammers!
Thanks for all the support, I am excited to finally get started. I will post updates as I move along. This is not my first engine build but it is my first Harley engine build. I have all the correct tools so hopefully it will go smoothly although, I may have a question or two along the way.
As far as the tuning, Scott recommended Ed at Dyno Difference in Dallas. I will do the first warm ups and then carry the bike to him. I will definitely post what I get. I hope it hammers!
As far as the tuning, Scott recommended Ed at Dyno Difference in Dallas. I will do the first warm ups and then carry the bike to him. I will definitely post what I get. I hope it hammers!
What did I do with my Dyna today .... I posted it on Craigslist. I have a 1991 HD Dyna Strugis that is being abused (sitting in the garage). I debated for months before I posted it for sale. I hope that I don't hate myself after I sell it.
The following users liked this post:
Dynawobble (01-05-2023)