What did you do to your Dyna today?
Got the old cams & bearings out, new ones in. Not too bad. Now the adjustable pushrods....those were a PITA for me! Tomorrow I need to clean off all of the oil, put on the exhaust and fire it up!
The following 4 users liked this post by Beerswimmer:
Bryan83taco (02-27-2022),
Dirtbandit (02-27-2022),
Garage Queen Rescue (02-27-2022),
Suede Blue Man (02-27-2022)
Done. The Thunderheader paint is as cheap as everyone says. The cams give a little lope to it, the idle is quieter but its louder when you give it some gas. The power increase is surprising!!!
The following 3 users liked this post by Beerswimmer:
This was the point of no return, fix it or tow it!!!
Old cams
YouTube University 😄
The following 5 users liked this post by Beerswimmer:
Bryan83taco (02-27-2022),
Garage Queen Rescue (02-28-2022),
Reindeer (03-01-2022),
Suede Blue Man (02-28-2022),
Uncle 'B' (02-27-2022)
Join Date: Jun 2018
Location: Lake Of The Ozarks MO, Hot Springs Arkansas
Posts: 245
Received 268 Likes
on
106 Posts
The following 4 users liked this post by LOTO:
Bryan83taco (02-28-2022),
Garage Queen Rescue (02-28-2022),
Jyruiz (03-04-2022),
Stiggy (02-28-2022)
Got new tail and head lights installed, krator fairing, curved license plate mount, and Bassani RR exhaust done yesterday. I got the RR2 with short muffler and it seems to be too close to my rear shock and the mounting bracket seems like it's going to run on the swingarm. Thinking a few washers will help with the clearance? Will post pics once I take them with the bike in the sun. Finished last night.
Got new tail and head lights installed, krator fairing, curved license plate mount, and Bassani RR exhaust done yesterday. I got the RR2 with short muffler and it seems to be too close to my rear shock and the mounting bracket seems like it's going to run on the swingarm. Thinking a few washers will help with the clearance? Will post pics once I take them with the bike in the sun. Finished last night.
Last edited by snake_eyes; 02-28-2022 at 11:12 AM.
The following users liked this post:
Cancun (02-28-2022)
Yesterday, I had 2 spare hours...FINALLY started the fork rebuild I've been posting about since last summer.
The following users liked this post:
Garage Queen Rescue (02-28-2022)
Got new tail and head lights installed, krator fairing, curved license plate mount, and Bassani RR exhaust done yesterday. I got the RR2 with short muffler and it seems to be too close to my rear shock and the mounting bracket seems like it's going to run on the swingarm. Thinking a few washers will help with the clearance? Will post pics once I take them with the bike in the sun. Finished last night.
Pics as promised.
The following 5 users liked this post by Cancun:
2500hdon37s (03-01-2022),
Garage Queen Rescue (02-28-2022),
JoeeJoee (03-01-2022),
Jyruiz (03-04-2022),
snake_eyes (03-01-2022)
Got rid of the dumb cowbell. Also routed the cables for a USB charger and the Powervision under the tank
The following 7 users liked this post by Beerswimmer:
Cancun (03-01-2022),
Garage Queen Rescue (03-01-2022),
Jay Guild (03-01-2022),
JoeeJoee (03-01-2022),
Jyruiz (03-04-2022),
and 2 others liked this post.
I managed to get this done last night. Gave her a good wash in the kitchen sink then sat down on the living room floor to swap bolts with ARPs and install the right-side rotor. My wife is the best!
The following 2 users liked this post by snake_eyes:
Garage Queen Rescue (03-01-2022),
Narddog (03-09-2022)