I just ordered a new FXBB
#52
06-08-2019 | 04:33 AM
Thread Starter
|
Stellar HDF Member
Joined: Feb 2017
Posts: 2,547
Likes: 980
From: East Flanders - Belgium
The following users liked this post:
HotRod917 (06-08-2019)
#53
06-10-2019 | 10:09 AM
Thread Starter
|
Stellar HDF Member
Joined: Feb 2017
Posts: 2,547
Likes: 980
From: East Flanders - Belgium
#55
06-11-2019 | 02:09 AM
Thread Starter
|
Stellar HDF Member
Joined: Feb 2017
Posts: 2,547
Likes: 980
From: East Flanders - Belgium
@vanceandhines Thanks!
I just love the products from V&H, got the exhausts and FP3 on all my bikes except on my FXFBS, for some reason I bought the Power Vision for that bike and honestly I must say I regret
this, I rather had a FP3 on it. The FP3 is so much easier to control and no extra stuff on the handle bar.
I just love the products from V&H, got the exhausts and FP3 on all my bikes except on my FXFBS, for some reason I bought the Power Vision for that bike and honestly I must say I regret
this, I rather had a FP3 on it. The FP3 is so much easier to control and no extra stuff on the handle bar.
#56
06-14-2019 | 01:35 AM
Sponsor
Joined: Mar 2018
Posts: 268
Likes: 52
From: California
Lots of great exhaust options. Congratulations on your new FXBB. FAB28 makes a nice system.
http://www.blackmillperformance.com/...arley-davidson
http://www.blackmillperformance.com/...arley-davidson
#57
06-14-2019 | 01:38 AM
Thread Starter
|
Stellar HDF Member
Joined: Feb 2017
Posts: 2,547
Likes: 980
From: East Flanders - Belgium
#58
06-14-2019 | 11:34 AM
Thread Starter
|
Stellar HDF Member
Joined: Feb 2017
Posts: 2,547
Likes: 980
From: East Flanders - Belgium
Just installed the CC kit, I did it slow this time and took me approx 25 minutes to install, now I have to program it but that will be for tomorrow.
The kit 41000369
Not much in the box
for plenty of money
The "old" ****
Removal
The rubber grommet in the frame with the connectors
2e picture of the rubber grommet
Removal of the existing wiring
The wire unp^lugged from the rubber grommet
Pull wire
The new CC installed
The connectors back in place
Done
The kit 41000369
Not much in the box
for plenty of money
The "old" ****
Removal
The rubber grommet in the frame with the connectors
2e picture of the rubber grommet
Removal of the existing wiring
The wire unp^lugged from the rubber grommet
Pull wire
The new CC installed
The connectors back in place
Done
Last edited by MoneyFor; 06-14-2019 at 11:35 AM.
#60
12-16-2019 | 05:06 PM
Thanks gys !
Just had a setback, I started unpacking the forwards and I almost had a heart attack, so much chrome ! ... the dealer missed in part n°'s so now I have to wait untill next tuesday before I get the right parts.
I did fabricate a sidemount licenseplate holder yesterday and just finished mounting them, sadly it is bad weather so I could not take a picture from a distance but here are a few. I made a one point mounting
in the hollow axle. I'm sure it will hold because I lift the bike if I try to move it.
Just had a setback, I started unpacking the forwards and I almost had a heart attack, so much chrome ! ... the dealer missed in part n°'s so now I have to wait untill next tuesday before I get the right parts.
I did fabricate a sidemount licenseplate holder yesterday and just finished mounting them, sadly it is bad weather so I could not take a picture from a distance but here are a few. I made a one point mounting
in the hollow axle. I'm sure it will hold because I lift the bike if I try to move it
.
