What did you do to your 18+ softail today?
#4342
I'm asking about the wires coming out of the left grip.
There are two plugs that come out of it it. One of them plugs into the plug on the bike that the guy pulls out right?
And then the other you plug into the harness that you solder the correct plug into, correct?
I know all that other stuff. I'm asking about the plugs that come out of the the left hand grip.
EDIT:
Ok so apparently both plugs he used came from the left grip. The first is the Throttle Wire that plugs into the plug that he's pulling out of the Wireloom. Plugs into the prepared wire that comes from the Left Hand grip that already matches.
The 2nd wire from the left hand grip plugs into the Y Harness that you modify with a matching connector from the kit provided in the heated grips kit.
I'm not sure why they have the throttle power wire route through and back to the left handgrip, but it's very annoying that it's unlabeled on the diagrams.
This was a simple but relatively annoying thing to figure out.
There are two plugs that come out of it it. One of them plugs into the plug on the bike that the guy pulls out right?
And then the other you plug into the harness that you solder the correct plug into, correct?
I know all that other stuff. I'm asking about the plugs that come out of the the left hand grip.
EDIT:
Ok so apparently both plugs he used came from the left grip. The first is the Throttle Wire that plugs into the plug that he's pulling out of the Wireloom. Plugs into the prepared wire that comes from the Left Hand grip that already matches.
The 2nd wire from the left hand grip plugs into the Y Harness that you modify with a matching connector from the kit provided in the heated grips kit.
I'm not sure why they have the throttle power wire route through and back to the left handgrip, but it's very annoying that it's unlabeled on the diagrams.
This was a simple but relatively annoying thing to figure out.
And yes, the other plug goes into the one you soldered.
And I assume that because the right side is pre wired for the grip, the black and white is just completing the circuit. The other is red and black that comes from the "Y" appears to be the ignition on power source.
The following users liked this post:
FranBunnyFFXII (11-10-2022)
#4343
The following 5 users liked this post by Jimbro:
Dcashskater (11-24-2022),
Gimlet (11-29-2022),
Glenn Gorman (11-18-2022),
WellAimedRound (11-25-2022),
wjcbsr (11-13-2022)
The following users liked this post:
Dcashskater (11-24-2022)
#4345
The following users liked this post:
snake_eyes (11-14-2022)
#4346
I cant install it yet, but I needed to share the beautiful thing I just unboxed that will be going on my bike here soon:
Galfer Wave Rotor 11.8inch with Galfer performance sintered pads to match.
330$ from FuelMoto USA.
I couldn't even order this off of Galfer's store front, FuelMoto had them, and ITS BEAUTIFUL. It's like a piece of jewelry, look at that glimmer.
God Damn I love FuelMoto's shop.
Galfer Wave Rotor 11.8inch with Galfer performance sintered pads to match.
330$ from FuelMoto USA.
I couldn't even order this off of Galfer's store front, FuelMoto had them, and ITS BEAUTIFUL. It's like a piece of jewelry, look at that glimmer.
God Damn I love FuelMoto's shop.
The following 10 users liked this post by FranBunnyFFXII:
andres.0321@hotmail.com (11-12-2022),
Dcashskater (11-24-2022),
FL_Moto (11-12-2022),
Glenn Gorman (11-18-2022),
gv550 (11-12-2022),
and 5 others liked this post.
#4347
I have no idea why HD cheaped out on this, but back a bit in the thread a bit there were some examples of grills being stuck to the inside of the oil cooler cover to protect the radiator or to simply look better.
Here's mine
You can also see the paint protection film I put on the regulator fins to help stop the paint getting chipped (and the dirt)
Here's mine
Car Mesh Grille, 100*30cm Universal Aluminium Alloy Car Racing Grill Net Vent Tuning Durable Honeycomb Grille Mesh for Bumper, Hood Vents, Fenders (3*6MM)
There are a few sellers on the big A selling the same stuff ...£16/$19 for a sheetYou can also see the paint protection film I put on the regulator fins to help stop the paint getting chipped (and the dirt)
Last edited by Gordon61; 11-14-2022 at 01:39 PM.
#4348
Join Date: Jun 2017
Location: Marineland Florida
Posts: 1,054
Likes: 0
Received 297 Likes
on
178 Posts
The following users liked this post:
murphc13 (11-14-2022)
#4349
The following 2 users liked this post by jazzkat:
murphc13 (11-14-2022),
WellAimedRound (11-25-2022)