What did you do to your 18+ softail today?
#3101
What did I do to my brand new softail today? I burnt the paint off my front fender as I bounced down the road like a fool with these new retro tires... all for the love of that retro look. I was astonished when I saw the paint on the front fender, and it took me a minute to figure out the tire was rubbing underneath. There was clearance on the front and rear of the fender, but apparently the shop didn’t think about centrifugal force. Only 500 miles on the bike. Yes, I know it’s not recommended to run retro tires on a new bike, but I had to try to see for myself. Can’t say I can recommend the Coker Beck tires. As great as they look to me, the bouncing / hopping is unacceptable. I have two older Harleys with retro tires that run as smooth as silk.
I will never go back to the stock tires, so I’ll try the Shinko 270’s next. I will have to get the front fender modified (sides cut and lengthened) for an extra eighth inch of clearance. And of course, repainted. Ideally I’d like to go without a fender, but I’d prefer the little bit of protection just in case. Needless to say I’m pretty disgusted after all the efforts of getting the tires installed by my local shop. Also noticed my back wheel had some serious defects in the powdercoat - not sure if Harley will cover that or not (cosmetic warrantee?)
I will never go back to the stock tires, so I’ll try the Shinko 270’s next. I will have to get the front fender modified (sides cut and lengthened) for an extra eighth inch of clearance. And of course, repainted. Ideally I’d like to go without a fender, but I’d prefer the little bit of protection just in case. Needless to say I’m pretty disgusted after all the efforts of getting the tires installed by my local shop. Also noticed my back wheel had some serious defects in the powdercoat - not sure if Harley will cover that or not (cosmetic warrantee?)
Last edited by Spumoni; 09-12-2021 at 02:29 PM.
The following users liked this post:
HarleyDEU (09-17-2021)
#3102
Just noticed the right rear light doesn't work on my 21 Slim. Lifted the seat and the molex connector is defective. Looks almost like its a bit melted. Bikes two weeks old. So I will be headed to the dealer this week for warranty. Hopefully they can find that dash rattle that kicks in at 1,740 rpm.
The following users liked this post:
Bayou FLHR-M8-128" (09-12-2021)
#3103
Do you have a factory gas cap ? If so I bet that’s your rattle, it was on my Fatboy and a bunch of other people on here. Several threads about it just search “gas cap rattle” , someone came up with a fix involving putting a couple dings on the inside of the cap with a hammer & punch. Worked for me...
The following users liked this post:
Bayou FLHR-M8-128" (09-12-2021)
#3104
What did I do to my brand new softail today? I burnt the paint off my front fender as I bounced down the road like a fool with these new retro tires... all for the love of that retro look. I was astonished when I saw the paint on the front fender, and it took me a minute to figure out the tire was rubbing underneath. There was clearance on the front and rear of the fender, but apparently the shop didn’t think about centrifugal force. Only 500 miles on the bike. Yes, I know it’s not recommended to run retro tires on a new bike, but I had to try to see for myself. Can’t say I can recommend the Coker Beck tires. As great as they look to me, the bouncing / hopping is unacceptable. I have two older Harleys with retro tires that run as smooth as silk.
I will never go back to the stock tires, so I’ll try the Shinko 270’s next. I will have to get the front fender modified (sides cut and lengthened) for an extra eighth inch of clearance. And of course, repainted. Ideally I’d like to go without a fender, but I’d prefer the little bit of protection just in case. Needless to say I’m pretty disgusted after all the efforts of getting the tires installed by my local shop. Also noticed my back wheel had some serious defects in the powdercoat - not sure if Harley will cover that or not (cosmetic warrantee?)
I will never go back to the stock tires, so I’ll try the Shinko 270’s next. I will have to get the front fender modified (sides cut and lengthened) for an extra eighth inch of clearance. And of course, repainted. Ideally I’d like to go without a fender, but I’d prefer the little bit of protection just in case. Needless to say I’m pretty disgusted after all the efforts of getting the tires installed by my local shop. Also noticed my back wheel had some serious defects in the powdercoat - not sure if Harley will cover that or not (cosmetic warrantee?)
#3105
What did I do to my brand new softail today? I burnt the paint off my front fender as I bounced down the road like a fool with these new retro tires... all for the love of that retro look. I was astonished when I saw the paint on the front fender, and it took me a minute to figure out the tire was rubbing underneath. There was clearance on the front and rear of the fender, but apparently the shop didn’t think about centrifugal force. Only 500 miles on the bike. Yes, I know it’s not recommended to run retro tires on a new bike, but I had to try to see for myself. Can’t say I can recommend the Coker Beck tires. As great as they look to me, the bouncing / hopping is unacceptable. I have two older Harleys with retro tires that run as smooth as silk.
I will never go back to the stock tires, so I’ll try the Shinko 270’s next. I will have to get the front fender modified (sides cut and lengthened) for an extra eighth inch of clearance. And of course, repainted. Ideally I’d like to go without a fender, but I’d prefer the little bit of protection just in case. Needless to say I’m pretty disgusted after all the efforts of getting the tires installed by my local shop. Also noticed my back wheel had some serious defects in the powdercoat - not sure if Harley will cover that or not (cosmetic warrantee?)
I will never go back to the stock tires, so I’ll try the Shinko 270’s next. I will have to get the front fender modified (sides cut and lengthened) for an extra eighth inch of clearance. And of course, repainted. Ideally I’d like to go without a fender, but I’d prefer the little bit of protection just in case. Needless to say I’m pretty disgusted after all the efforts of getting the tires installed by my local shop. Also noticed my back wheel had some serious defects in the powdercoat - not sure if Harley will cover that or not (cosmetic warrantee?)
It is a great look. If it was mine I would modify my mounting tabs to give me 1/4" prime it and ride. Then repaint come winter time.
And I am on my 2nd set of Shinko tires and love them. In all my years riding these Shinkos are the loudest tire I have ever had when it breaks loose. She barks loud enough for other riders to hear them when she breaks. Better riding and traction over the Dunlops.
Last edited by Bayou FLHR-M8-128"; 09-12-2021 at 05:20 PM.
#3106
Thank you for the compliment! The compressor is held by the electric center stand mount. The center stands mounts using the three rear oil pan bolts and two more higher up on the back of the motor/transmission. I think those two bolt holes are where the emissions gear on California bikes are mounted. I’ll try and get a picture and post it tomorrow.
#3107
Do you have a factory gas cap ? If so I bet that’s your rattle, it was on my Fatboy and a bunch of other people on here. Several threads about it just search “gas cap rattle” , someone came up with a fix involving putting a couple dings on the inside of the cap with a hammer & punch. Worked for me...
Last edited by motorend; 09-12-2021 at 08:30 PM.
#3108
The shop I go to is a friend of mine - he’s done other builds for me in the past, and is probably one of the most meticulous builders I’ve seen. He’s got OCD too, which is why we get along. There tire wasn’t touching in the front or rear of the fender, and it made no rubbing sounds. We just never thought about centrifugal force…
I think I’ll order a set of the Shinko 270’s…. MAYBE just maybe I won’t have to modify the tabs on the fender!
Glad to know you’re happy with the Shinko’s. Hopefully they won’t bounce like these Cokers do.
I think I’ll order a set of the Shinko 270’s…. MAYBE just maybe I won’t have to modify the tabs on the fender!
Glad to know you’re happy with the Shinko’s. Hopefully they won’t bounce like these Cokers do.
The following users liked this post:
Bayou FLHR-M8-128" (09-16-2021)
#3109
Join Date: Jun 2013
Location: My own little slice of heaven
Posts: 10,647
Received 5,294 Likes
on
2,899 Posts
#3110
Is it your clutch lever? Mine used to rattle really bad before I got new levers. Still rattles a bit but not nearly as bad with the upgraded sleeves.