The Everything Fat Bob Thread
#1681
#1684
#1685
Thundetbike torque handlebar installed in original riser
Finally my handlebar is installed by the dealer. They also installed cruisecontrol in the process.
my posture on the bike feels better! About 2,5” more pullback and about 1.5” higher. The bar is about 4” less wide. First impressions and handling feels good!
my posture on the bike feels better! About 2,5” more pullback and about 1.5” higher. The bar is about 4” less wide. First impressions and handling feels good!
The following 3 users liked this post by herwarth:
#1686
I have a pile of parts accumulating here and I’m itching to get them fitted!!
Some parts are at the powder coaters getting a matte black cerakote.
- Trask Assault Air Cleaner (outer ring, bolt heads and velocity stack to be cerakoted, also going to apply smoked film to the Perspex window)
- Trask Assault 2-1 exhaust (entire exhaust and heat shields/bolts to be cerakoted)
- Trask external breathers for air cleaner (bolt heads to be cerakoted)
- Trask CheckM8
- 2xBaja LP4 lights (will smoke tint the lenses)
- Bracket to mount lights
- Skene IQ-275 controller for light high/low beam
- Lower rocker covers (to be cerakoted)
- Assortment of black bolts to replace existing silver bolts around the bike.
This thing gon’ be murdered out!
Some parts are at the powder coaters getting a matte black cerakote.
- Trask Assault Air Cleaner (outer ring, bolt heads and velocity stack to be cerakoted, also going to apply smoked film to the Perspex window)
- Trask Assault 2-1 exhaust (entire exhaust and heat shields/bolts to be cerakoted)
- Trask external breathers for air cleaner (bolt heads to be cerakoted)
- Trask CheckM8
- 2xBaja LP4 lights (will smoke tint the lenses)
- Bracket to mount lights
- Skene IQ-275 controller for light high/low beam
- Lower rocker covers (to be cerakoted)
- Assortment of black bolts to replace existing silver bolts around the bike.
This thing gon’ be murdered out!
The following users liked this post:
jyx (08-31-2024)
#1687
Memphis shades installed and CarPlay screen
Worked on the bike yesterday. Installed Memphis shades. I get them to the painter next week to put gunship grey over the high gloss black finish.
Needed 12V ignition switched outlet for my Carpuride CarPlay screen. HD has got an assembly for that.
you have to open the USB box under the tank and put a cable harness into that. To open the USB box you have to lift the tank. It was a lot of work. Does anyone know how to remove the tank without removing the tacho on the tank?
The default tape put on by Memphis Shades. This is butt ugly and the double sided tape is visible and prone to dirt and insects
Got a car door protection strip from Amazon which makes an very nice and clean look
Needed 12V ignition switched outlet for my Carpuride CarPlay screen. HD has got an assembly for that.
you have to open the USB box under the tank and put a cable harness into that. To open the USB box you have to lift the tank. It was a lot of work. Does anyone know how to remove the tank without removing the tacho on the tank?
The default tape put on by Memphis Shades. This is butt ugly and the double sided tape is visible and prone to dirt and insects
Got a car door protection strip from Amazon which makes an very nice and clean look
Last edited by herwarth; 09-07-2024 at 10:29 AM.
The following users liked this post:
sterremos (09-07-2024)
Thread
Thread Starter
Forum
Replies
Last Post
Bluehighways
2014-2023 Touring Models
13
07-11-2022 07:25 AM