Air ride 2014+ dash switch part #?
#11
04-12-2017, 08:37 AM
I have utilized all my switches on my 2014 street glide without the harness mentioned. First you need to decide on standard or momentary switches depending on what you will be operating. Also Legacy Baggers(facebook) makes some nice stickers.
So for switches 2 thru 6 (starting from left to right) the wires are located under left side cover it is a gray plug. That plug also contains 12v, ign power and ground (so total of 8 wires) if you don't have service manual use test light to identify.
Once you decide what you are using each button for then you will know if you need to wire in a relay ie air ride will need relay, led lights no relay. 2 amps is the cutoff for relay.
If you don't want to cut the plug then go find the female plug that works and pin out your own plug. I decided against that for the ease of swapping switches when I change my mind.
If you want to use switch 1 then you need to locate the Blue/gray wire under the tank and tap that wire.
And yes that is a backup camera on my bike.
So for switches 2 thru 6 (starting from left to right) the wires are located under left side cover it is a gray plug. That plug also contains 12v, ign power and ground (so total of 8 wires) if you don't have service manual use test light to identify.
Once you decide what you are using each button for then you will know if you need to wire in a relay ie air ride will need relay, led lights no relay. 2 amps is the cutoff for relay.
If you don't want to cut the plug then go find the female plug that works and pin out your own plug. I decided against that for the ease of swapping switches when I change my mind.
If you want to use switch 1 then you need to locate the Blue/gray wire under the tank and tap that wire.
And yes that is a backup camera on my bike.
#12
04-12-2017, 09:41 AM
Stage III
Join Date: May 2016
Location: Ohio
Posts: 3
Likes: 0
Received 0 Likes
on
0 Posts
How do you wire in the relay? I guess that's my question and what relay do I buy? Just a small relay from the parts store? Because the harness has a relay attached to it so I can cut the connector off wire in my wires from my dirty air kit? Thanks
Last edited by Twilighttwinlight; 04-12-2017 at 09:41 AM. Reason: Typo
#13
04-12-2017, 10:23 AM
Buy the relay and it will show you how to wire. Gets a ground and 12v switch, signal in i.e. From air ride and wire to button.
#14
06-17-2018, 11:35 AM
I have utilized all my switches on my 2014 street glide without the harness mentioned. First you need to decide on standard or momentary switches depending on what you will be operating. Also Legacy Baggers(facebook) makes some nice stickers.
So for switches 2 thru 6 (starting from left to right) the wires are located under left side cover it is a gray plug. That plug also contains 12v, ign power and ground (so total of 8 wires) if you don't have service manual use test light to identify.
Once you decide what you are using each button for then you will know if you need to wire in a relay ie air ride will need relay, led lights no relay. 2 amps is the cutoff for relay.
If you don't want to cut the plug then go find the female plug that works and pin out your own plug. I decided against that for the ease of swapping switches when I change my mind.
If you want to use switch 1 then you need to locate the Blue/gray wire under the tank and tap that wire.
And yes that is a backup camera on my bike.
So for switches 2 thru 6 (starting from left to right) the wires are located under left side cover it is a gray plug. That plug also contains 12v, ign power and ground (so total of 8 wires) if you don't have service manual use test light to identify.
Once you decide what you are using each button for then you will know if you need to wire in a relay ie air ride will need relay, led lights no relay. 2 amps is the cutoff for relay.
If you don't want to cut the plug then go find the female plug that works and pin out your own plug. I decided against that for the ease of swapping switches when I change my mind.
If you want to use switch 1 then you need to locate the Blue/gray wire under the tank and tap that wire.
And yes that is a backup camera on my bike.
I want to do this exact setup! from left to right Switch #1 ACC (to power dirty air air ride and love jugs fans) #2 *** UP #3 *** DOWN #4 Center Stand down #5 Center Stand up #6 Air ride safety dump valve. I know this post is over a year old but, can you please advise what to buy and where for switches and maybe some pertinent wiring tips? I have a 14 Street Glide FLHX and only have #2 and #3 ACC switches. #3 currently powers up my fans and air ride. Any help would be greatly appreciated.
#15
10-25-2020, 02:22 PM
Stage III
Join Date: May 2016
Location: Ohio
Posts: 3
Likes: 0
Received 0 Likes
on
0 Posts
Thread
Thread Starter
Forum
Replies
Last Post