how do I get it to stop backfiring thru the carb?
Advanced
Joined: Nov 2005
Posts: 75
Likes: 0
From:
RE: how do I get it to stop backfiring thru the carb?
The enrichment screw is only an idle adjustment. If you look at the pic above that someone included it will help you make the changes yourself. It really is very simple. Change to a 45 or 48 slow jet, and a 170 main. This should correct your problem. The jets just screw in. Dealerships dont make any money on warrentee work so sometimes they are reluctant to be aggressive in getting to it. The jets are availible fgrom the dealer for about $5.
Goodluck,
Goodluck,
Intermediate
Joined: May 2006
Posts: 37
Likes: 0
From: Clinton, CT
RE: how do I get it to stop backfiring thru the carb?
I tryed real hard to get my dealer to fix the same problem... then leaving my HOG meeting the other day it farted and stalled as I was slow speed turning and I dumped it into a curb.
So make sure you fix it.. what started as a hassle for me became a big headache now[:@]
So make sure you fix it.. what started as a hassle for me became a big headache now[:@]
Road Master
Joined: Apr 2006
Posts: 782
Likes: 0
From: Shelton WA
RE: how do I get it to stop backfiring thru the carb?
Seems like a common problem for everyone, including me. In this forum you will find everyone who has tackeled this pulling the plug on the bottom of the carb and then screwing in the slow jet to seat (be gentle) and then backing out up to 2 turns depending on what else you have done to the bike, like pipes and jetting. The purpose of seating the jet is to get a starting point for your adjustment. You cannot see the screw while the carb is on the bike but you can adjust it onced the plug is removed. My dealer also blew smoke up you know where but I am starting to recognize the sensation. Bought a service manual and it walked me through the process. I felt better about doing it myself and learned a bit more about the bike in the process.
Tourer
Joined: May 2006
Posts: 311
Likes: 0
From: Chatham, ON
RE: how do I get it to stop backfiring thru the carb?
Could it be that your gas is lower than 91 octane. My '04 1200 will carb fart if I use 87 octane fuel. Gas mileage suffers greatly also if I use cheap 87 octane gas. I only use Sunoco Ultra 94.
Cruiser
Joined: May 2006
Posts: 242
Likes: 0
From: Rosemark, TN
RE: how do I get it to stop backfiring thru the carb?
Well, I adjusted the idle mix jet counter-clockwise as much as 1.5 turns from my starting point, then even played with it the other direction about a full turn. Still got the farts no matter where I set it. Its a random thing when riding, but I can reproduce easily if I try when its at idle and I rev it quickly. Really sucks.. The dealer jetted this thing, so they ought to be able to get it right. I'll probably call them tomorrow and take them a print out of this thread if I can make it over there.
Stage I
Joined: Jan 2007
Posts: 1
Likes: 0
RE: how do I get it to stop backfiring thru the carb?
I have a 6 month old 1200C also. It had the same symptoms as you're describing & also had a high-speed hesitation. The dealer replaced the intake & carb seals. Haven't riden much since then, but it seems to have fixed it. Maybe you can tell you lame dealer. I have it fixed at Orange County HD in Irvine, CA. Good luck.
Tourer
Joined: Jun 2006
Posts: 309
Likes: 0
From: DALLAS TEXAS
RE: how do I get it to stop backfiring thru the carb?
stage 1 solved all of my carb farts. only does it now if i shift too soon. just rejetting and adjusting the mixture works great for a cheap fix. since the bike is so lean you get a bigimprovement for about $100.00
Road Master
Joined: Jun 2006
Posts: 933
Likes: 1
From:
RE: how do I get it to stop backfiring thru the carb?
If your bike is an 06 you already have a 175 main jet on an 883.You would need to bump it up to a 180.The slow jet should be between a 45 and a 48 depending on location.Harley changed the needles so a bigger main jet was used.if you go in to change the main make sure you hold the tube it's in so I don't have to tell you how the other jet goes in.Make sure you replace the bowl screws with allen head screws.They are metric and I forget the size so take an old one with you.I got mine at a hardware store in stainless steel for under a buck each.There are 4 carb bowl screws.After you have the allens installed you can rejet as needed without even removing the air cleaner housing.Make sure you use a very good fitting phillps when you go to take out the carb bowl screws or they will strip out on you.
HD Forum Stories
The Best of Harley-Davidson for Lifelong Riders
Harley-Davidson Fat Boy Becomes a Dark, Decepticon-Inspired Custom
Verdad Gallardo
6 Weirdest Harley-Davidsons Ever Sold to the Public
Verdad Gallardo
7 Times Harley-Davidson Chucked Tradition Out the Window
Verdad Gallardo
7 Surprising Harley-Davidson Products that Are Not Motorcycles
Verdad Gallardo
8 Best Harley-Davidson Motorcycles Ever
Pouria Savadkouei
10 Worst Harley-Davidson Motorcycles Ever
Pouria Savadkouei
Killer Custom's Jail Break Is The Breakout That Refused to Blend In
Verdad Gallardo
Crazy Bunderbike Build Looks Amazing, But Is It Impossible to Ride?
Verdad Gallardo
Harley-Davidson Reveals Super Cool Cafe Racer Concept
Verdad Gallardo
Advanced
Joined: Jan 2007
Posts: 99
Likes: 0
From: West Fargo, ND
RE: how do I get it to stop backfiring thru the carb?
This same thing happens on my '06 1200C. I purchased a rejet kit off ebay for about 15 bucks including replacement bowl screws. I haven't installed them yet, as I won't be able to ride for a few months yet. My question is, Will rejetting this thing myself void the warranty? It has a year and a half left, so I don't want to lose this by tinkering. Also, how much does this affect fuel economy? I beleive the kit is 46 Pilot and 180 Main.
Tourer
Joined: Jan 2007
Posts: 303
Likes: 0
From:
RE: how do I get it to stop backfiring thru the carb?
my 2003 1200cc custom is killing me,,LOL
im glad to here it happens on new bikes as well
something has to be done on mine also..
its a cougher,,spitter what-ever
im glad to here it happens on new bikes as well
something has to be done on mine also..
its a cougher,,spitter what-ever