Did HD change the TSM/TSSM marry ?
Thread Starter
|
Tourer
Joined: Mar 2009
Posts: 469
Likes: 0
From: Maryland
Did HD change the TSM/TSSM marry ?
I have a 09 SG and bought the HD security. i have the table on how to marry the TSSM but my security light will not go off-even after 20 minutes. Did HD change the marrying procedures for 09 ?
Road Captain
Joined: Feb 2007
Posts: 704
Likes: 23
From: on the mud flats on the edge of slum city
I just read the 09 Electrical Diagnostic Manual and it appears to be the same as previous years for the password learn.
The fobs have to be programmed at the dealer with the DT2 though.
You do have the run switch set to RUN and you did try to start it once?
If you miss a step it won't work.
The fobs have to be programmed at the dealer with the DT2 though.
You do have the run switch set to RUN and you did try to start it once?
If you miss a step it won't work.
Thread Starter
|
Tourer
Joined: Mar 2009
Posts: 469
Likes: 0
From: Maryland
Switch set to RUN and it started and died just like it was supposed to. Waited 15 minutes for the security light to go off and it never did. I have tried several times and never get passed the first security light going off.
BTW-my fob is not a button fob-just a disk. Does that need programmed prior to the TSSM marry ?
BTW-my fob is not a button fob-just a disk. Does that need programmed prior to the TSSM marry ?
Road Captain
Joined: Feb 2007
Posts: 704
Likes: 23
From: on the mud flats on the edge of slum city
Yes the fob must be programmed at the dealers.
From the 2009 EDM
Ignition must be off for at least 15 seconds.
Install TSM/HFSM or ECM
Set engine stop switch to RUN
Turn ignition switch to ignition
Wait for engine and security lights to illuminate and then go out
Attempt normal start one time
Engine should start then stall and engine light should illuminate and stay on
Wait ten seconds then security lamp should illuminate
Wait for security lamp to go out (1o minutes)
Then turn ignition to off and back to ignition within one second
Security lamp should illuminate and wait for it to go out (10 minutes)
Then turn ignition to off and back to ignition within one second
Security lamp should illuminate and wait for it to go out (10 minutes)
Then turn ignition to off and back to ignition within one second
Then turn ignition switch to off for at least 15 seconds and then turn on and start bike.
See how you go with that but I would put the original TSM back in clear all codes and start again if I was you.
From the 2009 EDM
Ignition must be off for at least 15 seconds.
Install TSM/HFSM or ECM
Set engine stop switch to RUN
Turn ignition switch to ignition
Wait for engine and security lights to illuminate and then go out
Attempt normal start one time
Engine should start then stall and engine light should illuminate and stay on
Wait ten seconds then security lamp should illuminate
Wait for security lamp to go out (1o minutes)
Then turn ignition to off and back to ignition within one second
Security lamp should illuminate and wait for it to go out (10 minutes)
Then turn ignition to off and back to ignition within one second
Security lamp should illuminate and wait for it to go out (10 minutes)
Then turn ignition to off and back to ignition within one second
Then turn ignition switch to off for at least 15 seconds and then turn on and start bike.
See how you go with that but I would put the original TSM back in clear all codes and start again if I was you.
Cruiser
Joined: Jul 2007
Posts: 199
Likes: 0
From: West Central Wisconsin
Yes the fob must be programmed at the dealers.
From the 2009 EDM
Ignition must be off for at least 15 seconds.
Install TSM/HFSM or ECM
Set engine stop switch to RUN
Turn ignition switch to ignition
Wait for engine and security lights to illuminate and then go out
Attempt normal start one time
Engine should start then stall and engine light should illuminate and stay on
Wait ten seconds then security lamp should illuminate
Wait for security lamp to go out (1o minutes)
Then turn ignition to off and back to ignition within one second
Security lamp should illuminate and wait for it to go out (10 minutes)
Then turn ignition to off and back to ignition within one second
Security lamp should illuminate and wait for it to go out (10 minutes)
Then turn ignition to off and back to ignition within one second
Then turn ignition switch to off for at least 15 seconds and then turn on and start bike.
See how you go with that but I would put the original TSM back in clear all codes and start again if I was you.
From the 2009 EDM
Ignition must be off for at least 15 seconds.
Install TSM/HFSM or ECM
Set engine stop switch to RUN
Turn ignition switch to ignition
Wait for engine and security lights to illuminate and then go out
Attempt normal start one time
Engine should start then stall and engine light should illuminate and stay on
Wait ten seconds then security lamp should illuminate
Wait for security lamp to go out (1o minutes)
Then turn ignition to off and back to ignition within one second
Security lamp should illuminate and wait for it to go out (10 minutes)
Then turn ignition to off and back to ignition within one second
Security lamp should illuminate and wait for it to go out (10 minutes)
Then turn ignition to off and back to ignition within one second
Then turn ignition switch to off for at least 15 seconds and then turn on and start bike.
See how you go with that but I would put the original TSM back in clear all codes and start again if I was you.
I used these instructions this afternoon to marry a new security module on my bike.
Followed them step-by step, the bike started fine on first try.
(Next week I'll have the dealer program it for my FOBs.)
-stef
Cruiser
Joined: May 2007
Posts: 189
Likes: 0
From: Birmingham, AL
Yes the fob must be programmed at the dealers.
From the 2009 EDM
Ignition must be off for at least 15 seconds.
Install TSM/HFSM or ECM
Set engine stop switch to RUN
Turn ignition switch to ignition
Wait for engine and security lights to illuminate and then go out
Attempt normal start one time
Engine should start then stall and engine light should illuminate and stay on
Wait ten seconds then security lamp should illuminate
Wait for security lamp to go out (1o minutes)
Then turn ignition to off and back to ignition within one second
Security lamp should illuminate and wait for it to go out (10 minutes)
Then turn ignition to off and back to ignition within one second
Security lamp should illuminate and wait for it to go out (10 minutes)
Then turn ignition to off and back to ignition within one second
Then turn ignition switch to off for at least 15 seconds and then turn on and start bike.
See how you go with that but I would put the original TSM back in clear all codes and start again if I was you.
From the 2009 EDM
Ignition must be off for at least 15 seconds.
Install TSM/HFSM or ECM
Set engine stop switch to RUN
Turn ignition switch to ignition
Wait for engine and security lights to illuminate and then go out
Attempt normal start one time
Engine should start then stall and engine light should illuminate and stay on
Wait ten seconds then security lamp should illuminate
Wait for security lamp to go out (1o minutes)
Then turn ignition to off and back to ignition within one second
Security lamp should illuminate and wait for it to go out (10 minutes)
Then turn ignition to off and back to ignition within one second
Security lamp should illuminate and wait for it to go out (10 minutes)
Then turn ignition to off and back to ignition within one second
Then turn ignition switch to off for at least 15 seconds and then turn on and start bike.
See how you go with that but I would put the original TSM back in clear all codes and start again if I was you.
Trending Topics
Tourer
Joined: Aug 2005
Posts: 291
Likes: 18
From: Kentucky
Yes the fob must be programmed at the dealers.
From the 2009 EDM
Ignition must be off for at least 15 seconds.
Install TSM/HFSM or ECM
Set engine stop switch to RUN
Turn ignition switch to ignition
Wait for engine and security lights to illuminate and then go out
Attempt normal start one time
Engine should start then stall and engine light should illuminate and stay on
Wait ten seconds then security lamp should illuminate
Wait for security lamp to go out (1o minutes)
Then turn ignition to off and back to ignition within one second
Security lamp should illuminate and wait for it to go out (10 minutes)
Then turn ignition to off and back to ignition within one second
Security lamp should illuminate and wait for it to go out (10 minutes)
Then turn ignition to off and back to ignition within one second
Then turn ignition switch to off for at least 15 seconds and then turn on and start bike.
See how you go with that but I would put the original TSM back in clear all codes and start again if I was you.
From the 2009 EDM
Ignition must be off for at least 15 seconds.
Install TSM/HFSM or ECM
Set engine stop switch to RUN
Turn ignition switch to ignition
Wait for engine and security lights to illuminate and then go out
Attempt normal start one time
Engine should start then stall and engine light should illuminate and stay on
Wait ten seconds then security lamp should illuminate
Wait for security lamp to go out (1o minutes)
Then turn ignition to off and back to ignition within one second
Security lamp should illuminate and wait for it to go out (10 minutes)
Then turn ignition to off and back to ignition within one second
Security lamp should illuminate and wait for it to go out (10 minutes)
Then turn ignition to off and back to ignition within one second
Then turn ignition switch to off for at least 15 seconds and then turn on and start bike.
See how you go with that but I would put the original TSM back in clear all codes and start again if I was you.
Thanks
HD Forum Stories
The Best of Harley-Davidson for Lifelong Riders
Harley-Davidson Fat Boy Becomes a Dark, Decepticon-Inspired Custom
Verdad Gallardo
6 Weirdest Harley-Davidsons Ever Sold to the Public
Verdad Gallardo
7 Times Harley-Davidson Chucked Tradition Out the Window
Verdad Gallardo
7 Surprising Harley-Davidson Products that Are Not Motorcycles
Verdad Gallardo
8 Best Harley-Davidson Motorcycles Ever
Pouria Savadkouei
10 Worst Harley-Davidson Motorcycles Ever
Pouria Savadkouei
Killer Custom's Jail Break Is The Breakout That Refused to Blend In
Verdad Gallardo
Crazy Bunderbike Build Looks Amazing, But Is It Impossible to Ride?
Verdad Gallardo
