'07 Fork Oil Change
Thread Starter
|
Extreme HDF Member
Joined: Sep 2005
Posts: 11,615
Likes: 50
From: Baton Rouge, LA
'07 Fork Oil Change
The procedure in the '07 service manual for a fork-oil change specifies removing the fork, fork-tube plug, and spring (among other things)--then inverting the fork for the fluid to drain. Looking at the parts manual I can't figure out why you couldn't simply use the drain plug, then remove the top plug and add the new oil from the top.
For those of you who've changed the fork oil in your '06 or later FLH, here are some questions:
(1) Is the fork-tube plug (45838-77) hollow so that oil can pass through it when added from the top hole?
(2) Will all fork oil drain from the drain plug, assuming the forks are pumped repeatedly?
If the answers to both are "yes," I can't see why a fork-oil change wouldn't be only a matter of draining, moving the top plug, then adding oil at the top.
Changing the fork oil in my old '96 RK was a 15-min. proposition by just draining and applying a vacuum at the schrader valve to suck the new oil in through the drain plug. If all the oil could be drained from that fork, why not the newer models? I'm not talking about cartidge type forks, but the forks HD has been making for the past few years.
For those of you who've changed the fork oil in your '06 or later FLH, here are some questions:
(1) Is the fork-tube plug (45838-77) hollow so that oil can pass through it when added from the top hole?
(2) Will all fork oil drain from the drain plug, assuming the forks are pumped repeatedly?
If the answers to both are "yes," I can't see why a fork-oil change wouldn't be only a matter of draining, moving the top plug, then adding oil at the top.
Changing the fork oil in my old '96 RK was a 15-min. proposition by just draining and applying a vacuum at the schrader valve to suck the new oil in through the drain plug. If all the oil could be drained from that fork, why not the newer models? I'm not talking about cartidge type forks, but the forks HD has been making for the past few years.
Thread Starter
|
Extreme HDF Member
Joined: Sep 2005
Posts: 11,615
Likes: 50
From: Baton Rouge, LA
Thanks, that answers my first question. Now, will all oil drain out from the drain plug? I would assume that even if it didn't I could drain, refill, and repeat one or more times until the fluid is clear--then refill with the same amount originally drained. That might not be the best method, but if done every 10k it would be better than no change at all. Then at 50k do a disassemble and change it as per the book.
My bike had about 7500 miles on it when I put on the chrome lowers. The fork oil that drained out was sooo dirty, I don't think you could get it all out by removing just the plug at the bottom. What ever you end up doing, when you put in the new oil, use the heavier SE fork oil. It eliminates alot of the dive when braking.
Thread Starter
|
Extreme HDF Member
Joined: Sep 2005
Posts: 11,615
Likes: 50
From: Baton Rouge, LA
I was planning on using the SE oil, or another 15W. I may try draining from the bottom and perhaps cycling new oil several times to clean it out by pumping the forks.
Road Warrior
Joined: Nov 2006
Posts: 1,462
Likes: 121
From: Northern Illinois
I've heard before that some of the dealers have a cool piece of apparatus that sucks the old fork oil out and replaces it with new through the drain hole. This sounds like a good way to go if there is such a thing. Anybody know for sure?
Thread Starter
|
Extreme HDF Member
Joined: Sep 2005
Posts: 11,615
Likes: 50
From: Baton Rouge, LA
I don't see an advantage to using this method with newer bikes, as you'd still need to remove the top plug to release the vacuum in the fork, and if it's already off you might as well install the new oil from the top. If you could seal the opening you could apply the vacuum from the top and suck it through the drain plug as with the older bikes, but again I see no advantage to going to the extra effort.
Trending Topics
Advanced
Joined: Mar 2008
Posts: 95
Likes: 0
I ride an 07 ultra and this is the way I change fork oil.
1. Remove outer fairing.
2. Remove radio-to access top fork caps.
3. Remove top cap from one side.
4. Remove drain plug from that side and drain.
5. Slowly fill with oil from top and slowly work forks up and down until full.
6. Repeat for other side
1. Remove outer fairing.
2. Remove radio-to access top fork caps.
3. Remove top cap from one side.
4. Remove drain plug from that side and drain.
5. Slowly fill with oil from top and slowly work forks up and down until full.
6. Repeat for other side
HD Forum Stories
The Best of Harley-Davidson for Lifelong Riders
Harley-Davidson Fat Boy Becomes a Dark, Decepticon-Inspired Custom
Verdad Gallardo
6 Weirdest Harley-Davidsons Ever Sold to the Public
Verdad Gallardo
7 Times Harley-Davidson Chucked Tradition Out the Window
Verdad Gallardo
7 Surprising Harley-Davidson Products that Are Not Motorcycles
Verdad Gallardo
8 Best Harley-Davidson Motorcycles Ever
Pouria Savadkouei
10 Worst Harley-Davidson Motorcycles Ever
Pouria Savadkouei
Killer Custom's Jail Break Is The Breakout That Refused to Blend In
Verdad Gallardo
Crazy Bunderbike Build Looks Amazing, But Is It Impossible to Ride?
Verdad Gallardo
Harley-Davidson Reveals Super Cool Cafe Racer Concept
Verdad Gallardo
Thread Starter
|
Extreme HDF Member
Joined: Sep 2005
Posts: 11,615
Likes: 50
From: Baton Rouge, LA
BTW, you can access the top plugs by removing the ignition switch and fairing cap, which IMO is easier than removing the radio.