TSM/TSSM programing
Thread Starter
|
6th Gear
Joined: Oct 2004
Posts: 12
Likes: 0
TSM/TSSM programing
I bought a ignition module for my 2004 FXSTS it states in the instructions that i need to consult my owners manual because my TSM/TSSM will need to be synced?
I do not have the alarm (TSSM) so only the TSM and it really does not tell me what i need to do. I see the on-off-on-off-on and then press left TS twice shows one blink means no code. But what do I need to sync up the new module. I was told if i dont do this the bike will not start.
Any help?
I do not have the alarm (TSSM) so only the TSM and it really does not tell me what i need to do. I see the on-off-on-off-on and then press left TS twice shows one blink means no code. But what do I need to sync up the new module. I was told if i dont do this the bike will not start.
Any help?
Banned
Joined: Oct 2004
Posts: 278
Likes: 0
From:
RE: TSM/TSSM programing
The procedure is a s follows:
Ign off for at least 15 sec.
Install ICM
Set run/off to run on rt hand control.
Turn ign key on
Wait ten seconds. Security lamp will light and stay on.
Wait until security lamp turns off.
Quickly (within two seconds) turn ign key off-on.
Wait until security lamp turns off.
Quickly (within two seconds) turn ign key off - on. (second time)
Wait until security lamp turns off.
Quickly (within two seconds) turn ign key off - on. (third time)
Turn ign key off. Wait 15 seconds before turning IGN on. Turn IGN switch on and start the engine to confirm successful password learning procedure. Clear trouble codes.
That should "sync" the ICM to the TSM and ECM.
Sorry for the mix-up before!
BClem
Ign off for at least 15 sec.
Install ICM
Set run/off to run on rt hand control.
Turn ign key on
Wait ten seconds. Security lamp will light and stay on.
Wait until security lamp turns off.
Quickly (within two seconds) turn ign key off-on.
Wait until security lamp turns off.
Quickly (within two seconds) turn ign key off - on. (second time)
Wait until security lamp turns off.
Quickly (within two seconds) turn ign key off - on. (third time)
Turn ign key off. Wait 15 seconds before turning IGN on. Turn IGN switch on and start the engine to confirm successful password learning procedure. Clear trouble codes.
That should "sync" the ICM to the TSM and ECM.
Sorry for the mix-up before!
BClem
Banned
Joined: Oct 2004
Posts: 278
Likes: 0
From:
RE: TSM/TSSM programing
Are you saying that the bike would NOT start? All you are doing is allowing the system to recognise the ICM and vice versa. Not rocket science. Explain what happened when you went through the procedure....
BClem
BClem
Thread Starter
|
6th Gear
Joined: Oct 2004
Posts: 12
Likes: 0
RE: TSM/TSSM programing
yes the bike fires once and then a code gets set.
I started by following the inst.
run to run
turn ing. on once light goes off, turn off-on, once light goes back off off-on, once light goes off, off-on again third time. once light turns off turn ing. back to off wiat 15 sec and the ing. back on and press start.
Did i miss something? Do I have to do something before this proceedure? I really dont want to take the bike into harley. They always seem to do something wrong. I have had 5 bikes over that last 10 years and have always done my own work. This computer stuff sucks. My last bike was a 2002 RK fuel injected. I hated it. always over heated. Found this new springer carb had to have it.
I do very much appriciate your help.
I started by following the inst.
run to run
turn ing. on once light goes off, turn off-on, once light goes back off off-on, once light goes off, off-on again third time. once light turns off turn ing. back to off wiat 15 sec and the ing. back on and press start.
Did i miss something? Do I have to do something before this proceedure? I really dont want to take the bike into harley. They always seem to do something wrong. I have had 5 bikes over that last 10 years and have always done my own work. This computer stuff sucks. My last bike was a 2002 RK fuel injected. I hated it. always over heated. Found this new springer carb had to have it.
I do very much appriciate your help.
Trending Topics
Banned
Joined: Oct 2004
Posts: 278
Likes: 0
From:
RE: TSM/TSSM programing
What code is being set?
The procedure includes installing (pluging in the ICM) after a minimum time with the Ign off. Now try pulling the ECM fuse (upper left most 15A fuse under the 40A main) for a minimum of fifteen minutes, then go through the procedure again. A Harley mechanic told me about that trick...
BClem
The procedure includes installing (pluging in the ICM) after a minimum time with the Ign off. Now try pulling the ECM fuse (upper left most 15A fuse under the 40A main) for a minimum of fifteen minutes, then go through the procedure again. A Harley mechanic told me about that trick...
BClem
HD Forum Stories
The Best of Harley-Davidson for Lifelong Riders
Harley-Davidson Fat Boy Becomes a Dark, Decepticon-Inspired Custom
Verdad Gallardo
6 Weirdest Harley-Davidsons Ever Sold to the Public
Verdad Gallardo
7 Times Harley-Davidson Chucked Tradition Out the Window
Verdad Gallardo
7 Surprising Harley-Davidson Products that Are Not Motorcycles
Verdad Gallardo
8 Best Harley-Davidson Motorcycles Ever
Pouria Savadkouei
10 Worst Harley-Davidson Motorcycles Ever
Pouria Savadkouei
Killer Custom's Jail Break Is The Breakout That Refused to Blend In
Verdad Gallardo
Crazy Bunderbike Build Looks Amazing, But Is It Impossible to Ride?
Verdad Gallardo
Harley-Davidson Reveals Super Cool Cafe Racer Concept
Verdad Gallardo
Banned
Joined: Oct 2004
Posts: 278
Likes: 0
From:
RE: TSM/TSSM programing
We are overlooking someting very basic. You have reinstalled the old one and "everything is fine" so I'm wondering why the replacement? The old one is not malfunctioning? Do you disconnect the battery when you perform these exchanges?
This is getting interesting, I will delve into finding a solution because my manual says that you must reprogram the ICM/ECM with a 'Digital Technician' available 'only' to Harley mechanics. If this is the case, I'm going to sell this Harley... I refuse to be totally dependent on some inept clown in an "H.D. Mechanic"'s shirt. Bullshit! I'm more disgruntled all the time with Harley Davidson. They're even keeping information from anyone/everyone who purchases their manuals... So a dealer can soak you? Screw that!
I still cannot figure out how an HD mechanic determined that a totally disconnected electronic device was the problem with my 2500RPM high (cold) idle. They are geniuses! They blamed a device that they do not understand but sell and install for 'performance' applications. The manual states that the ECM/ICM can be reprogrammed for higher performance - Stage 1, Stage2, etc., and will continue warranty if THEY install oversized barrels on a twin cam engine. If I install them, the warranty is voided. Lots of contradictions and deception, and entrapment!
Sorry for the rant..., nonproductive.
BClem
This is getting interesting, I will delve into finding a solution because my manual says that you must reprogram the ICM/ECM with a 'Digital Technician' available 'only' to Harley mechanics. If this is the case, I'm going to sell this Harley... I refuse to be totally dependent on some inept clown in an "H.D. Mechanic"'s shirt. Bullshit! I'm more disgruntled all the time with Harley Davidson. They're even keeping information from anyone/everyone who purchases their manuals... So a dealer can soak you? Screw that!
I still cannot figure out how an HD mechanic determined that a totally disconnected electronic device was the problem with my 2500RPM high (cold) idle. They are geniuses! They blamed a device that they do not understand but sell and install for 'performance' applications. The manual states that the ECM/ICM can be reprogrammed for higher performance - Stage 1, Stage2, etc., and will continue warranty if THEY install oversized barrels on a twin cam engine. If I install them, the warranty is voided. Lots of contradictions and deception, and entrapment!
Sorry for the rant..., nonproductive.
BClem